Zontes ZT350-EURO V 2022, Руководство по обслуживанию

Страница: 14 / 118

2-FRAME & ENGINE COMPONENT
13
CHK
ADJ
NO. PART NO. PART NAME QTY CAUTION
1 1251112-003093 M6×45 Hex flange surface 9.8 bolt (color Zinc) 2 10N.m
2 4050854-002051 ZT310-R engine left rear cover (dark gray) 1
3 1251300-057093 Non-standard nut M10×1.5(Dacromet) 4
4 1274300-082000 ZT350-R engine hanger 2
5 1251100-060000 Non-standard bolts M10X1.5X90 (Dacromet) 2
6 1251100-132003 Non-standard bolt M10×1.5×80 (Dacromet) 2
7 1250305-009091 GB6187.1 M12×1.25(White Zinc) 2
8 4024300-003021 ZT350-R bracket 1
9 1251112-019000 GB5187 non-standard bolt M12×1.25×85 2
10 1251112-023000 GB5187 non-standard bolt M12×1.25×95 2
11 1251300-067000 ZT250-R rear wheel hollow shaft nut 1
12 1252200-040000 ZT310-R1 rear flat fork hollow shaft Φ20×315 1
13 1251100-262000 Non-standard bolt M12×1.25×127(Dacromet) 1
Fig.1 FRAME & ENGINE
COMPONENT
Engine component
PROCEDURE:
After removing the barrier, the bangs connected to the hanging piece and the bracket connection should be re -
inserted so that the later operation can be operated.
●
Engine left rear cover
The left rear cover
⑵
of the engine removes the bolt
⑴
with an 8#sleeve.
●
The middle part of the engine is connected with the frame and the rear flat fork
Fix the head of bolt
⑸
and bolt
⑹
at the connection butween the upper part of the engine and the frame with
14# sleeve,and remove nut
⑶
with 14# sleeve.Only remove other nuts of the nut cannot be removed.Use
14#sleeve to fix the bolts
⑼
and bolts
⑽
at the head at the head of the bracket, and then remove the nut
⑺
at the
17#sleeve.Use 14#sleeve to fix the bolt at the head of the engine, and then remove the nut
⑺
for 17#sleeve.You
cannot remove the bolts
⑸
,
⑹
,
⑼
,
⑽
, and hanging slices
⑷
.
●
Remove the engine
Disassemble the engine with a 24#opening wrench and fix the head of the flat fork shaft, and remove the nut
⑾
with a 30#sleeve.One person shakes slightly after the flat fork assembly, and the one will draw a flat fork shaft
⑿ 一
A.At the same time, the two hold the engine left and right boxes; one person removes the bolts, bolts, and
hanging slices at the hanging slices, and then remove the bolts, bolts and brackets on the front bracket, and
finally take it. The bolts hanging under the engine.Keeping the engine into one side, pay attention to safety during
the movement. Put the engine on the flat ground.
CAUTION:
●
The coolant should be drained before disassembly.
●
It is necessary to remove the seat cushion, fuel tank, side cover, pedal support, wind deflector,lower
shroud component,shift lever, muffler, radiator and pipe, cable, air filter joint, chain, positive wire of the
motor, etc.
●
The waste oil needs to be collected and returned to qualified institutions. It is forbidden to dump and
pollute the environment and the source of water.
●
All standard parts must meet the standard torque value when reassembling, and refill the engine oil
according to the operation instruction.