Watts Aerco BMK 750 Скачать руководство пользователя страница 3

Страница: 3 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

CONTENTS

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

157

5.2 LOW GAS PRESSURE TEST .............................................................................................................. 72

5.2.1

LOW GAS PRESSURE TEST: BMK750

–

2500 ................................................................................................... 72

5.2.2

LOW GAS PRESSURE TEST: BMK3000

–

6000 Only ........................................................................................ 74

5.3 HIGH GAS PRESSURE TEST ............................................................................................................. 78

5.3.1

HIGH GAS PRESSURE TEST: BMK750

–

2500 .................................................................................................. 78

5.3.2

HIGH GAS PRESSURE TEST: BMK3000

–

6000 Only ........................................................................................ 80

5.4 LOW WATER LEVEL FAULT TEST ..................................................................................................... 84

5.5 WATER TEMPERATURE FAULT TEST .............................................................................................. 85

5.6 INTERLOCK TESTS ............................................................................................................................. 86

5.6.1

Remote Interlock Test .................................................................................................................................... 86

5.6.2

Delayed Interlock Test ................................................................................................................................... 87

5.7 FLAME FAULT TEST ............................................................................................................................ 88

5.8 AIR FLOW FAULT TESTS - BLOWER PROOF & BLOCKED INLET SWITCHES .............................. 89

5.8.1

Blower Proof Switch Test ............................................................................................................................... 89

5.8.2

Blocked Inlet Switch Test ............................................................................................................................... 91

5.9 SSOV PROOF OF CLOSURE SWITCH CHECK ................................................................................. 92

5.10 PURGE SWITCH OPEN DURING PURGE ........................................................................................ 93

5.11 IGNITION SWITCH OPEN DURING IGNITION ................................................................................. 95

5.12 SAFETY PRESSURE RELIEF VALVE TEST ..................................................................................... 95

SECTION 6.

STANDALONE MODES OF OPERATION ......................................... 97

6.1 OUTDOOR AIR RESET MODE ............................................................................................................ 97

6.1.1

Outdoor Air Temperature Sensor Installation ............................................................................................... 97

6.1.2

Outdoor Reset Mode Startup ........................................................................................................................ 98

6.2 CONSTANT SETPOINT MODE ........................................................................................................... 99

6.3 REMOTE SETPOINT MODE ................................................................................................................ 99

6.4 DIRECT DRIVE MODES..................................................................................................................... 100

6.5 AERCO CONTROL SYSTEM (ACS) .................................................................................................. 101

6.6 COMBINATION CONTROL SYSTEM (CCS) ..................................................................................... 101

6.6.1

Combination Control System Field Wiring ................................................................................................... 102

6.6.2

Combination Control System Setup and Startup ......................................................................................... 102

SECTION 7.

BOILER SEQUENCING TECHNOLOGY .......................................... 105

7.1 INTRODUCTION ................................................................................................................................. 105

7.1.1

Installation Notes.......................................................................................................................................... 106

7.2 BST QUICK START CHART .............................................................................................................. 106

7.3 BST IMPLEMENTATION INSTRUCTION .......................................................................................... 107

7.3.1

Option 1 Constant Setpoint: Direct Wired Header Temp Sensor ................................................................ 107

7.3.2

Option 2 Constant Setpoint: Modbus Wired Header Temp Sensor ............................................................. 109

7.3.3

Option 3 Outdoor Reset: Direct Wired Header Temp Sensor & Direct Wired Outdoor Sensor .................. 111

7.3.4

Option 4 Outdoor Reset: Modbus Header Temp Sensor & Modbus Outdoor Temp Sensor ....................... 113

7.3.5

Option 5 Remote Setpoint: Direct Wired Header Temp Sensor & 4-20ma Setpoint Drive ......................... 116

7.3.6

Option 6 Remote Setpoint: Direct Wired Header Temp Sensor & Modbus Setpoint Drive ........................ 118

7.3.7

Option 7 Remote Setpoint: Modbus Header Temp Sensor & 4-20ma Setpoint Drive ................................. 120

7.3.8

Option 8 Remote Setpoint: MODBUS Header Temp Sensor & MODBUS Setpoint Drive ............................ 122

SECTION 8.

MAINTENANCE .......................................................................... 125

8.1 MAINTENANCE SCHEDULE ............................................................................................................. 125

8.2 IGNITER-INJECTOR

– BMK750 - 4000 ............................................................................................. 126

8.3 PILOT IGNITION ROD

– BMK5000 & 6000 ....................................................................................... 128

8.4 FLAME DETECTOR ........................................................................................................................... 128

8.5 O

SENSOR 129

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды