Watts Aerco BMK 750 Скачать руководство пользователя страница 116

Страница: 116 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 7

– BOILER SEQUENCING TECHNOLOGY

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

116

157

7.3.5

Option 5 Remote Setpoint: Direct Wired Header Temp Sensor & 4-20ma

Setpoint Drive

OPTION 5

Instructions: Remote Setpoint, Direct Wired Header Temp Sensor, 4-20ma Setpoint

Drive

NOTE:

Both

Header Temp Sensor

and

4-20ma Direct Drive

must be wired. See the

Edge [i]

Controller Manual

(OMM-0141, GF-213-B) for more information.

Step 1: HEADER TEMP SENSOR WIRING

– BST MANAGER Unit

1. On the

BST

Manager

unit, connect the

Header Temp Sensor

to the

Feed Forward

(FFWD)

terminals on the P-1 Harness via the terminal block labeled

Header Temp sensor

on the I/O Board.

2. Ground the shield to any

SHLD

terminal on the I/O Board.

NOTES:

•

The

Header Temp Sensor

must be installed between 2 and 10 feet (0.61 and 3.1m)

downstream of the

last

boiler in the plant’s supply water header.

•

Shielded pair 18 - 22 AWG cable is recommended for

Header Temp Sensor

wiring.

There is no polarity to be observed. The ground for the shield is at the

SHLD

terminal

on the I/O Board. The sensor end of the shield must be left free and ungrounded.

Step 2: DIRECT WIRED 0-20mA or 4-20mA WIRING

– BST MANAGER Unit

1. Connect the

4-20mA

0-20mA

terminals from the Direct Drive source to the

Ain+

and

Ain-

terminals on the BST Manager

’s I/O Board.

2. Connect the shield to any

SHLD

terminal on the I/O Board.

NOTES:

•

Shielded pair 18 - 22 AWG cable is recommended for this connection. Polarity must be

observed.

•

The ground for the shield is at the driver signal source.

Continued on next page

HEADER TEMP SENSOR

I/O BOARD

HEADER TEMP SENSOR

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды