Watts Aerco BMK 750 Скачать руководство пользователя страница 119

Страница: 119 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 7

– BOILER SEQUENCING TECHNOLOGY

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

119

157

OPTION 6

Instructions: Remote Setpoint, Direct Wired Header Temp Sensor, Modbus Setpoint

Drive

NOTES:

•

Polarity must be observed for the RS485 connections.

•

Connect the shield to any

SHLD

terminal on the I/O Board.

•

When mounting the

Outdoor Temp Sensor

, it must be located on the North side of the

building where an average outside air temperature is expected. The sensor must be
shielded from direct sunlight as well as impingement by the elements. The outdoor
sensor may be wired up to 200 feet (61m) from the boiler.

•

There is no polarity to be observed. The ground for the shield is at the power supply

ground. The sensor end of the shield must be left free and ungrounded.

Step 3

– OPTION 6 CONFIGURATION

On All Boiler:

1. Go to:

Main Menu

→

Advanced Setup

→

BST Cascade

→

Cascade Configuration

•

Set the

Unit Mode

parameter to

BST Client

2. Go to:

Main Menu

→

Advanced Setup

→

BST Cascade

→

Application Configuration

•

Set the

Unit Address

parameter to the communication address of the unit.

On the BST Manager only

1. Go to

Main Menu

→

Advanced Setup

→

BST Cascade

, set the Parameters to the Values

in each menu in the table below.

Menu/Screen Name

Parameters

Values

Cascade
Configuration

Unit Mode

BST Manager

Hdr Temp Sensor

Header Temp

Application
Configuration

Application

Space Heating

SH Operating Mode

Rmt Setpt Netwrk

Cascade Comm

Min address

The

minimum

unit address in the cascade

Max address

The

maximum

unit address in the cascade

Cascade Baud Rate

The baud rate for the cascade.

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды