Watts Aerco BMK 750 Скачать руководство пользователя страница 109

Страница: 109 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 7

– BOILER SEQUENCING TECHNOLOGY

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

109

157

7.3.2

Option 2 Constant Setpoint: Modbus Wired Header Temp Sensor

OPTION 2

Instructions: Constant Setpoint with Modbus Wired Header Temp Sensor

Step 1: MODBUS HEADER TEMP SENSOR WIRING

– ANY BOILER

Using the Modbus Transmitter provides gives the plant the ability to use the Backup

manager feature. This allows the any of the client units to become a Backup manager if
the manager unit is not communicating.

1. Connect the

Modbus Transmitter

terminal

Pin B

to the

RS485+

terminal, and

Pin A

the

RS485-

terminal on the I/O Board of any Boiler unit, using shielded pair 18 - 22 AWG

cable.

2. Connect the

Header Temp Sensor

to pins

and

of the

Modbus Transmitter

using

shielded pair 18 - 22 AWG cable.

3. Install a jumper wire between pins

and

of the

Modbus Transmitter

NOTES:

•

Polarity must be observed for the RS485 connections.

•

Ground the shield to any

SHLD

terminal on the I/O Board.

•

The

Header Temp Sensor

must be installed between 2 and 10 feet (0.61 and 3.1m)

downstream of the

last

boiler in the plant’s supply water header.

•

There is no polarity to be observed. The ground for the shield is at the power supply

ground. The sensor end of the shield must be left free and ungrounded.

Step 2: OPTION 2 CONFIGURATION

On All Boiler:

1. Go to:

Main Menu

→

Advanced Setup

→

BST Cascade

→

Cascade Configuration

•

Set the

Unit Mode

parameter to

BST Client

2. Go to:

Main Menu

→

Advanced Setup

→

BST Cascade

→

Application Configuration

•

Set the

Unit Address

parameter to the communication address of the unit.

Continued on next page

MODBUS TRANSMITTER

HEADER TEMP SENSOR

I/O BOARD

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды