Watts Aerco BMK 750 Скачать руководство пользователя страница 2

Страница: 2 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

CONTENTS

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

157

Table of Contents

TABLE OF CONTENTS ........................................................................................... 2

FOREWORD ...................................................................................................... 5

SECTION 1.

SAFETY PRECAUTIONS ................................................................... 9

1.1 WARNINGS & CAUTIONS ..................................................................................................................... 9

1.2 EMERGENCY SHUTDOWN ................................................................................................................. 10

1.3 PROLONGED SHUTDOWN ................................................................................................................. 10

1.4 IMPORTANT

– FOR MASSACHUSETTS INSTALLATIONS ............................................................... 11

SECTION 2.

EDGE [I] CONTROLLER OPERATION .............................................. 13

2.1 INTRODUCTION ................................................................................................................................... 13

2.2 LOGIN AND PASSWORD ENTRY ....................................................................................................... 14

2.3 MENU STRUCTURE ............................................................................................................................ 15

2.3.1

Unit Status Menu ........................................................................................................................................... 15

2.3.2

Calibration Menu ........................................................................................................................................... 16

2.3.3

Diagnostics Menu........................................................................................................................................... 17

2.3.4

Advanced Setup Menu ................................................................................................................................... 20

SECTION 3.

START SEQUENCE ........................................................................ 31

3.1 INTRODUCTION ................................................................................................................................... 31

3.2 START SEQUENCE ............................................................................................................................. 31

3.3 START/STOP LEVELS ......................................................................................................................... 39

3.4 START/STOP LEVELS

– AIR/FUEL & ENERGY INPUT ..................................................................... 40

3.4.1

BMK750/1000 Air/Fuel Valve Position and Energy Input .............................................................................. 40

3.4.2

BMK1500 Air/Fuel Valve Position and Energy Input ...................................................................................... 41

3.4.3

BMK2000 Air/Fuel Valve Position and Energy Input ...................................................................................... 42

3.4.4

BMK2500 Air/Fuel Valve Position and Energy Input ...................................................................................... 43

3.4.5

BMK3000 Air/Fuel Valve Position and Energy Input ...................................................................................... 44

3.4.6

Benchmark4000 Air/Fuel Valve Position and Energy Input ........................................................................... 45

3.4.7

Benchmark5000 Air/Fuel Valve Position and Energy Input ........................................................................... 46

3.4.8

Benchmark6000 Air/Fuel Valve Position and Energy Input ........................................................................... 47

SECTION 4.

INITIAL START-UP ........................................................................ 49

4.1 INITIAL START-UP REQUIREMENTS ................................................................................................. 49

4.2 TOOLS & INSTRUMENTS FOR COMBUSTION CALIBRATION ........................................................ 50

4.2.1

Required Tools & Instrumentation ................................................................................................................ 50

4.2.2

Installing Gas Supply Manometer .................................................................................................................. 50

4.2.3

Accessing the Analyzer Probe Port ................................................................................................................ 54

4.3 FUEL TYPES AND COMBUSTION CALIBRATION ............................................................................. 55

4.4 COMBUSTION CALIBRATION ............................................................................................................. 55

4.4.1

NATURAL GAS Manual Combustion Calibration ............................................................................................ 56

4.4.2

PROPANE GAS COMBUSTION CALIBRATION .................................................................................................. 61

4.5 REASSEMBLY ...................................................................................................................................... 66

4.6 DUAL FUEL SWITCHOVER ................................................................................................................. 67

4.7 OVER-TEMPERATURE LIMIT SWITCHES ......................................................................................... 68

4.7.1

Digital Alarm Switch Checks and Adjustments............................................................................................... 69

SECTION 5.

SAFETY DEVICE TESTING .............................................................. 71

5.1 TESTING OF SAFETY DEVICES ......................................................................................................... 71

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды