Watts Aerco BMK 750 Скачать руководство пользователя страница 15

Страница: 15 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 2: OPERATION

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

157

2.3 MENU STRUCTURE

The Main Menu give you access to all Edge [i] Controller user functionality. There are four major
divisions within the menu structure.

Figure 3.3: The Edge [i] Controller Main Menu

2.3.1

Unit Status Menu

The

Unit Status

menu contains the following sections and parameters. Unlike other Edge

menus, navigation starts at the

Unit Status

screen and proceeds from there by scrolling right.

Main Menu

→

Unit Status

Target Fire Rate

Read Only

The target Fire Rate (0% to 100%).

Current Fire Rate

Read Only

The current Fire Rate (0% to 100%).

Flame Strength

Read Only

The current Flame Strength (0% to 100%).

Inlet Temp

Read Only

The current Inlet Water temperature

Setpoint

Read Only

The

unit’s current Setpoint.

Outlet

Read Only

The current Outlet temperature.

Air Inlet

Read Only

The current Air Inlet temperature.

Read Only

The Current O

reading.

Exhaust

Read Only

The current Exhaust temperature.

Main Menu

→

Plant Status

– BST Manager Only

Outside Temp

Read Only

The reading of the outside temperature meter

SH/Other Setpoint

Read Only

The BST cascade’s current Setpoint.

SH/Other Supply

Read Only

The supply temperature reading.

Inlet Temp

Read Only

The inlet temperature reading.

Units Available

Read Only

The number of units in the BST cascade.

Units Firing

Read Only

The number of units in the BST cascade firing.

Units Online

Read Only

The number of units in the BST cascade online.

SH/Other Fire Rate

Read Only

The fire rate for the BST cascade.

Main Menu

→

BST Cascade Status

– BST Manager Only

SH/Other Fire Rate

Read Only

The fire rate for the BST cascade.

Units Online

Read Only

The number of units in the BST cascade online.

SH/Other Setpoint

Read Only

The BST cascade’s current Setpoint.

Units Available

Read Only

The number of units in the BST cascade available.

Sh/Other Supply

Read Only

The supply temperature reading.

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды