Watts Aerco BMK 750 Скачать руководство пользователя страница 72

Страница: 72 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 5

– SAFETY DEVICE TESTING

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

157

5.2 LOW GAS PRESSURE TEST

Complete the instructions in Section 5.2.1 for BMK750

– 2500 units, or in Section 5.2.2 for

BMK3000

– 6000 units, which have different Low and High Gas Pressure switches.

5.2.1

LOW GAS PRESSURE TEST: BMK750

–

2500

To simulate a low gas pressure fault, refer to Figure

5-1a to 5-1c and perform the following

steps:

LOW Gas Pressure Test Instructions: BMK750

– 2500

Remove the front panel from the boiler to access the gas train components.

Close the leak detection ball valve located at the Low Gas Pressure switch.

Remove the 1/4" NPT plug from the ball valve at the Low Gas Pressure switch.

Install a

0 -

16” W.C. (0 – 4.0 kPa)

manometer or gauge where the 1/4" plug was removed.

Slowly open the 1/4" ball valve near the Low Gas Pressure switch.

On the Controller, go to

Main Menu

→

Diagnostics

→

Manual Mode

Enable the

Manual

Mode

parameter. The

Comm

LED will go off and the

MANUAL

LED will light.

Adjust the Air/Fuel Valve position

between 25% and 30%

using the

(Plus) and

–

(Minus) controls.

While the unit is firing, slowly close the external manual gas shut-off valve upstream of the unit (not
shown).

10.

The unit should shut down and display a

Fault Lockout -

Gas Pressure

Fault

message at

approximately the pressure shown in Table 5-1 (the pressure setting of the Low Gas Pressure
switch):

TABLE 5-1: LOW

Gas Pressure, ± 0.2” W.C. (± 50 Pa)

Benchmark Model

Natural Gas

Propane

BMK750/1000 FM & DBB Single-Fuel

2.6” W.C. (648 Pa)

7.5” W.C. (1,868 Pa)

BMK1500/2000 FM & DBB Single-Fuel

3.6” W.C. (897 Pa)

–

BMK1500/2000 Dual-Fuel

4.4” W.C. (1,096 Pa)

2.6” W.C. (648 Pa)

BMK1500/2000 DBB Dual-Fuel

2.6” W.C. (648 Pa)

BMK2500 FM & DBB Single-Fuel

3.6” W.C. (897 Pa)

–

BMK2500 Dual-Fuel

7.5” W.C. (1,868 Pa)

3.6” W.C. (897 Pa)

BMK2500 DBB Dual-Fuel

7.5” W.C. (1,868 Pa)

3.6” W.C. (897 Pa)

11.

Close the ball valve near the Low Gas Pressure switch (opened in Step 5).

12.

Fully open the external manual gas shut-off valve (not shown) and press the Controller

’s

CLEAR

button.

13.

The fault message should clear, the

FAULT

indicator should go off, and the unit should restart.

14.

Upon test completion, close the ball valve, remove the manometer and replace the 1/4" NPT plug
removed in step 3.

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды