Watts Aerco BMK 750 Скачать руководство пользователя страница 23

Страница: 23 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 2: OPERATION

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

157

Warm Weather Shtdwn

Numeric Entry

Client/Manager

The threshold outside temperature above which the
unit shuts down (

Outdoor Air Temp Sens

Network

Direct

BAS

Auto-Manager Transfer

Toggle

Manager

Allows BST Manger functionality to be transferred
to another unit if the BST Manger malfunctions.

Auto Failover Type

Toggle

Manager

Choose either C-More or Edge 2.

Auto-Manager Timer

Numeric Entry

Manager

Specifies duration of BST Manger malfunction that
triggers

Auto-Manager Transfer

(10 to 120).

Auto-Manager Addr

Read Only

Manager

The address of the current BST Manger (0 to 16).

Backup Manager Addr

Numeric Entry

Manager

The address of the unit designated as the Backup
BST Manger (0 to 16).

Hdr Temp Sensor

Select

Manager

Choose how the unit communicates with the
Header Temp Sensor:

Off

Network

FFWD Temp

BAS

SH Sensor Comm Addr

Numeric Entry

Client/Manager

Specify the Modbus transmitter address (0 to 255,

Outdoor Air Temp Sens

Hdr Temp Sensor

DHW Temp Sensor

Network

BAS

SH Hdr Temp Point

Numeric Entry

Manager

The Modbus point within the Modbus address of
the Header Temp Sensor (0 to 255,

Outdoor Air

Temp Sens

Hdr Temp Sensor

DHW Temp

Sensor

Network

BAS

DHW Temp Sensor

Select

Manager

Choose how to communicate with the DHW
temperature sensor:

Off

Network

Direct

BAS

(in the Application Configuration screen,

Application

Other

DHW Hdr Sens Point

Numeric Entry

Manager

Specify the Modbus point within the Modbus
address where the DHW temp sensor resides
(

DHW Temp Sensor

Network

BAS

DHW Temp Unit Addr

Numeric Entry

Manager

Specify the unit to which the DHW Header Temp
Sensor is connected

(0 to 16,

DHW Temp Sensor

Direct

Rtn Hdr Temp Sensor

Select

Manager

Choose how the unit communicates with
Header Temp Sensor:

Off

Network

BAS

Rtn Hdr Sens Point

Numeric Entry

Manager

The Modbus point within the Modbus address of
the Header Temp Sensor (0 to 255,

Rtn Hdr Temp

Sensor

Network

Outdoor Air Temp Sens

Select

Client/Manager

Once Enabled, specifies how the outdoor air
temperature sensor communicates. Choose:

Off

BAS

Direct

Network

Outdoor Temp Addr

Numeric Entry

Manager

The Modbus transmitter address of the outdoor
temp sensor (0 to 255,

Outdoor Air Temp Sens

Network

OAT Temp Point

Numeric Entry

Manager

The Modbus point within the Modbus address of
the Outside Air Temp Sensor (0 to 255,

Outdoor

Air Temp Sens

Network

Main Menu

→

Advanced Setup

→

BST Cascade

→

Cascade Communication

Parameter Name

Type

BST Client

BST Manager

Description

Unit Address

Numeric Entry

Client/Manager

The unit’s address in the BST cascade.

Min Address

Numeric Entry

Manager

The minimum address in the BST cascade (1 to
16).

Max Address

Numeric Entry

Manager

The maximum address in the BST cascade (1 to
16).

Cascade Baud Rate

Select

Client/Manager

The communication baud rate in the cascade.

Plant Failsafe Mode

Toggle

Client/Manager

The unit/

plant’s operating mode if communication is

lost:

Shutdown

Constant Setpoint

Plant Failsafe Setpoint

Numeric Entry

Client/Manager

The unit/

plant’s setpoint if communication is lost

(

Unit

Failsafe Mode

Constant Setpoint

Network Timeout

Numeric Entry

Client/Manager

The timeout before a Modbus Fault is declared (5
to 999 sec.).

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды