Watts Aerco BMK 750 Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 157

background image

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 8

– MAINTENANCE

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

136

of

157

8.10.1

Rear Refractory Replacement

Rear Refractory Replacement Instructions

1. Turn off gas and electrical power to the unit. In addition, turn off any other units sharing the

exhaust flue.

2. Disconnect the flue from the exhaust manifold of the boiler being serviced and remove flue

sections up to the top of the unit enclosure.

3. Remove the small O

2

Sensor Cover from the rear sheet metal enclosure panel. The Air

Eductor assembly is clipped to the bottom edge of this opening. Lift the Air Eductor assembly
up off the left-rear panel, then secure it in place with a length of cord or wire.

DO NOT

REMOVE THE LEFT-REAR PANEL

without first securing the Air Eductor assembly in place.

NOTE:

At the top, the left and right-rear panels are attached to the left and right top rails by nuts. At
the bottom, each rear panel is attached to the base with one nut each. Access the nuts for
removal through the side panel, as shown in Figure 8-8.

4. Remove the left-rear panel, which is held in place by 2 spring

latches and 7/16” bolts, inside

the panel on the top rail and bottom lip. See Figure 8-8, below.

5. With the panels removed, the rear plate of the combustion chamber can be accessed, as

shown in Figure 8-9, below.

CAUTION!

The surfaces of the heat exchanger may be hot. Allow the unit to cool sufficiently before
proceeding to the next step.

6. Remove the O

2

sensor and the 1/4” stainless steel tube from the rear plate.

7. Disconnect the wires from the thermal switch on the rear plate.

8. Remove all of the nuts from the rear plate, EXCEPT for the one at the top of the plate.

9. Loosen (but DO NOT REMOVE) the top nut and slide a thin metal object (such as a hacksaw

blade) between the rear plate and the fiber material of the rear refractory to separate the
material from the plate.

CAUTION!

The rear plate weighs approximately 40 pounds. It is therefore recommended that 2 people
remove the plate.

10. Remove the top nut from the plate and remove it from the unit.

11. Optionally, you can thread 2 small nipples into the rear plate to act as handles, which will

ease removal and reinstallation.

«
...
134
135
136
137
138
...
»

Содержание Aerco BMK 750






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aerco BMK 750

Бренд: ideal commercial Страницы: 36

White Boiler WH 80

Бренд: Ravenheat Страницы: 68

Бренд: Daikin Страницы: 416

Electric Smokeless Broiler

Бренд: Saladmaster Страницы: 12

Бренд: Baxi Страницы: 16

PREMIER PLUS 400

Бренд: Baxi Страницы: 16

PREMIER PLUS 1000L

Бренд: Baxi Страницы: 20

Classic FF 3 100

Бренд: Ideal Boilers Страницы: 40

Q Premier QP130N

Бренд: Rinnai Страницы: 94

Бренд: H2O Страницы: 50

Бренд: Unical Страницы: 44

Бренд: Hydro-Smart Страницы: 58

Бренд: Burnham Страницы: 8

Бренд: Ferroli Страницы: 36

Бренд: Gledhill Response Страницы: 12

Бренд: Saunier Duval Страницы: 32

Бренд: gledhill Страницы: 32

Бренд: Potterton Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды