Watts Aerco BMK 750 Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 157

background image

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 7

– BOILER SEQUENCING TECHNOLOGY

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

114

of

157

OPTION 4

Instructions: Outdoor Reset, Modbus Header Temp Sensor & Modbus Outdoor

Temp Sensor

NOTES:

•

Polarity must be observed for the RS485 connections.

•

Ground the shield at any

SHLD

terminal in the I/O the Board.

•

When mounting the Outdoor sensor, it must be located on the North side of the building

where an average outside air temperature is expected. The sensor must be shielded
from direct sunlight as well as impingement by the elements. The outdoor sensor may
be wired up to 200 feet (61m) from the boiler.

•

There is no polarity to be observed. The ground for the shield is at the power supply

ground. The sensor end of the shield must be left free and ungrounded.

Step 3

– OPTION 4 CONFIGURATION

Using the Modbus Transmitter provides gives the plant the ability to use the Backup
manager feature. This allows the any of the client units to become a Backup manager if
the manager unit is not communicating.

On All Boiler:

1. Go to:

Main Menu

→

Advanced Setup

→

BST Cascade

→

Cascade Configuration

:

•

Set the

Unit Mode

parameter to

BST Client

.

2. Go to:

Main Menu

→

Advanced Setup

→

BST Cascade

→

Application Configuration

:

•

Set the

Unit Address

parameter to the communication address of the unit.

On the BST Manager only:

1. Go to

Main Menu

→

Advanced Setup

→

BST Cascade

, set the Parameters to the Values

in each menu in the table below.

Menu/Screen Name

Parameters

Values

Cascade
Configuration

Auto Manager Transfer

Enabled (This is available on the Manger unit
only)

Auto failover Type

C-More

Backup Manager Address Enter the designated backup unit address

Unit Mode

BST Manager

Hdr Temp Sensor

Network

Sensor

Comm Address

240

Hdr Temp Point

14

Application
Configuration

Application

Space Heating

SH Operating Mode

Outdoor Reset

MODBUS TRANSMITTER

OUTDOOR TEMP SENSOR

I/O BOARD

«
...
112
113
114
115
116
...
»

Содержание Aerco BMK 750






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aerco BMK 750

Бренд: Radiant Страницы: 16

Бренд: Laars Страницы: 4

Бренд: Protherm Страницы: 32

Бренд: Ariston Страницы: 68

Бренд: Calomax Страницы: 14

Бренд: Patterson-Kelley Страницы: 101

HydroTap G5 Touch-Free Wave

Бренд: Zip Страницы: 44

REMEHA W40-m ECO

Бренд: broag Страницы: 40

Бренд: sylber Страницы: 32

Бренд: CAC / BDP Страницы: 32

Бренд: Truma Страницы: 60

Бренд: Ideal Heating Страницы: 29

Бренд: ACV Страницы: 14

Бренд: ACV Страницы: 30

Бренд: ACV Страницы: 38

Eurocondense three

Бренд: Potterton Страницы: 120

Tube Steel Boilers

Бренд: Bryan Boilers Страницы: 8

Бренд: Viessmann Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды