Watts Aerco BMK 750 Скачать руководство пользователя страница 18

Страница: 18 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 2: OPERATION

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

157

2.3.3.2

Main Menu

→

Diagnostics

→

Front Panel

Main Menu

→

Diagnostics

→

Front Panel

Touchscreen Display Test

On/Off

Starts the Touchscreen Display Test.

Touchscreen Test

On/Off

Starts the Touchscreen Test.

Status Light Test

On/Off

Starts the Status Light Test.

Keypad and Switch Test

On/Off

Starts the Keypad and Switch Test.

2.3.3.3

Main Menu

→

Diagnostics

→

Analog Outputs and Relays

Main Menu

→

Diagnostics

→

Analog Outputs and Relays

→

Relays

Ignition Relay

Enable/Disable

Enables/Disables the Ignition Relay.

Blower Relay

Enable/Disable

Enables/Disables the Blower Relay.

Pump Relay

Enable/Disable

Enables/Disables the Pump Relay.

Aux Relay

Enable/Disable

Enables/Disables the Aux Relay.

Fault Relay

Enable/Disable

Enables/Disables the Fault Relay.

Main Menu

→

Diagnostics

→

Analog Outputs and Relays

→

Analog Outputs

Valve

Read/Adjust

Adjustable display of the A/F valve Position.

Blower

Read/Adjust

Adjustable display of the Blower.

2.3.3.4

Main Menu

→

Diagnostics

→

Subsystems

Main Menu

→

Diagnostics

→

Subsystems

→

Air Fuel Valve Stepper Motor

Auto Stroke

Toggle

Initiates A/F cycle, 0 to 100 to 0%

Valve Position In

Adjust

Manual adjustment of A/F Valve 0 to 100%.

Main Menu

→

Diagnostics

→

Subsystems

→

Blower

Profile

Select

Select the profile to run (default =

Profile 1

Profile Run

Enable/Disable

Enables running the selected profile.

Blower

Numeric Entry

Manually adjust the Blower

’s voltage.

Main Menu

→

Diagnostics

→

Subsystems

→

Ignition

Ignition Spark

Enable/Disable

Enables testing the unit’s ignition spark.

Spark Current

Read Only

The current Spark Current.

2.3.3.5

Main Menu

→

Diagnostics

→

System

Main Menu

→

Diagnostics

→

System

→

Pre-Start Up

Pre-Start Up Mode

Enable/Disable

Enables Pre-Start Up Mode, a test of various system
components without firing the unit.

Valve Position Out

Read Only

The current A/F valve position.

Blower (voltage)

Read Only

The current Blower voltage.

Blower (RPM)

Read Only

The current Blower RPM.

Spark Current

Read Only

The current Spark Current.

Flame Strength

Read Only

The current flame strength.

Gas pressure

Read Only

The current gas pressure.

Main Menu

→

Diagnostics

→

System

→

Versions

Serial Number

Read Only

The unit’s serial number.

Software Version

Read Only

The Controller’s software version.

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды