Watts Aerco BMK 750 Скачать руководство пользователя страница 111

Страница: 111 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 7

– BOILER SEQUENCING TECHNOLOGY

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

111

157

7.3.3

Option 3 Outdoor Reset: Direct Wired Header Temp Sensor & Direct Wired

Outdoor Sensor

OPTION 3

Instructions: Outdoor Reset, Direct Wired Header Temp Sensor & Outdoor Sensor

NOTE:

Both

Header Temp Sensor

and

Outdoor Sensor

must be wired. See the

Edge [i]

Controller Manual

(OMM-0141, GF-213-B) for more information.

Step 1: DIRECT WIRED

HEADER TEMP SENSOR WIRING

– BST MANAGER Unit

1. On the

BST Manager

unit, connect the

Header Temp Sensor

to the Feed Forward

(FFWD) terminals on the P-1 Harness via the terminal block labeled

Header Temp sensor

on the I/O Board.

2. Ground the shield to any

SHLD

terminal on the I/O Board.

NOTES:

•

The

Header Temp Sensor

must be installed between 2 and 10 feet (0.61 and 3.1m)

downstream of the

last

boiler in the plant’s supply water header.

•

Shielded pair 18 - 22 AWG cable is recommended for

Header Temp Sensor

wiring.

There is no polarity to be observed. Ground the shield to the

Shield

terminal on the I/O

Board. The sensor end of the shield must be left free and ungrounded.

Step 2: DIRECT WIRED

OUTDOOR SENSOR WIRING

– BST MANAGER Unit

1. On the

BST Manager

Unit, connect the

Outdoor Temp Sensor

to the

OUT

and

COM

terminals on the I/O Board.

2. Connect the shield to any

SHLD

terminal on the I/O Board.

NOTES:

•

Twisted shielded pair 18 - 22 AWG cable is recommended for

Header Temp Sensor

wiring. There is no polarity to be observed. The sensor end of the shield must be left
free and ungrounded.

•

When mounting the Outdoor sensor, it

must be located on the North side of the

building

where an average outside air temperature is expected. The sensor must be

shielded from direct sunlight as well as impingement by the elements. The outdoor
sensor may be wired up to 200 feet (61m) from the boiler.

OUTDOOR TEMP SENSOR

HEADER TEMP SENSOR

I/O BOARD

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды