Watts Aerco BMK 750 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 157

background image

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 3 - START SEQUENCE

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

31

of

157

SECTION 3.

START SEQUENCE

3.1 INTRODUCTION

The information in this section provides a guide to starting the Benchmark Boiler using the Edge
[i] Controller. It is imperative that the initial startup of this unit be performed by factory trained
personnel. Operation prior to initial startup by factory trained personnel may void the equipment
warranty. In addition, the following WARNINGS and CAUTIONS must be observed at all times.

WARNING!

•

All of the installation procedures in Section 2:

Installation

in the

Benchmark 750-6000 with

Edge [i]: Install-Startup Manual

(OMM-0144, GF-217) must be completed before the initial

start-up of the unit.

•

Electrical voltages up to

120 VAC (BMK750

– 2000), 208 or 480 VAC (BMK2500 - 4000),

or 208

,

480

or

575

VAC (BMK5000 & 6000)

and 24 volts AC

may be used in this

equipment. It must be serviced only by factory certified service technicians.

•

Do not attempt to dry fire the unit

. Starting the unit without a full water level can seriously

damage the unit and may result in injury to personnel or property damage. This situation
will void any warranty.

•

Initial startup of the unit

must be

performed by AERCO factory trained personnel.

Operation prior to initial startup by factory trained personnel may void the equipment
warranty. In addition, the following WARNINGS and CAUTIONS must be observed at all
times.

3.2 START SEQUENCE

When the Edge [i] Controller Enable/Disable switch is set to the

Enable

position, it checks all pre-

purge safety switches to ensure they are closed. These switches include:

•

High Water Temperature switch

•

High Gas Pressure switch

•

Low Gas Pressure switch

•

Low Water Level switch

•

Safety Shut-Off Valve (SSOV) Proof of Closure (POC) switch

NOTE:

The

Blocked Inlet

and downstream

Blower Proof

switches are

not

checked prior to starting

the pre-purge.

If all of the above switches are closed, the READY light (above the Enable/Disable switch) will
light when the switch is in the

Enable

position and the unit will be in the STANDBY mode.

NOTE:

If any of the Pre-Purge safety device switches are open, or the required conditions are not
observed throughout the start sequence, appropriate fault messages will be displayed.

When there is a demand for heat, the following events occur:

«
...
29
30
31
32
33
...
»

Содержание Aerco BMK 750






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aerco BMK 750

Бренд: Vaillant Страницы: 20

Little Star LS 80

Бренд: Ravenheat Страницы: 4

Бренд: Raypak Страницы: 40

Бренд: Kalvis Страницы: 16

Бренд: Kalor Страницы: 54

Ciao S 20 C.S.I.

Бренд: Beretta Страницы: 31

Бренд: R&V Works Страницы: 12

MultiTemp MR Series

Бренд: HydroTherm Страницы: 36

Бренд: Velocity Страницы: 160

Condexa Pro 100 P

Бренд: Riello Страницы: 23

Mighty Therm HH 1010

Бренд: Laars Страницы: 28

Бренд: Laars Страницы: 44

Бренд: Strebel Страницы: 30

Бренд: Columbia Страницы: 32

Бренд: Viessmann Страницы: 168

Бренд: Vaillant Страницы: 28

Бренд: Thermo Dynamics Страницы: 24

Бренд: Thermo Dynamics Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды