Watts Aerco BMK 750 Скачать руководство пользователя страница 88

Страница: 88 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 5

– SAFETY DEVICE TESTING

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

157

5.7 FLAME FAULT TEST

Flame faults can occur during ignition or while the unit is already running. To simulate each of
these fault conditions, proceed as follows:

Flame Fault Test Instructions

1. Set the

Controller’s

Enable/Disable

switch to

Disable

2. On the Controller, go to:

Main Menu

→

Diagnostics

→

Manual Mode

3. Enable the

Manual Run

control.

4. Set the valve position

between 25% and 30%

using the

(Plus) and

–

(Minus) controls.

5. Close the gas tra

in’s Manual Shutoff valve located between the Safety Shut-Off Valve

(SSOV) and the Air/Fuel Valve, as shown on Figure 5-3a to 5-3c, above.

6. It may be necessary to jump out the High Gas Pressure switch.

7. Set the

Controller’s

Enable/Disable

switch to

Enable

to start the unit.

8. The unit should purge and light the Pilot flame and then shut down after reaching the main

Burner Ignition cycle and display

Flame Loss During Ign

9. Open the Manual Shutoff valve closed in step 5 and press the

CLEAR

soft key.

10. Restart the unit and allow it to prove flame.

11. Once flame is proven, close the Manual Shutoff valve located between the SSOV and the

Air/Fuel Valve (see Figure 5-3a to 5-3c, above).

12. The unit should shut down and do one of the following:

BMK750

– 2000 units

: the unit will execute an

IGNITION RETRY

cycle by performing

the following steps:

•

The unit will execute a shutdown purge cycle for a period of 15 seconds and
display

Wait Fault Purge

•

The unit will execute a 30 second re-ignition delay and display Wait Retry Pause.

•

The unit will then execute a standard ignition sequence and display Wait Ignition
Retry.

•

Since the Manual Shutoff valve is still closed, the unit will fail the ignition retry
sequence. Therefore, it will shut down and display

Flame Loss During Ign

following the IGNITION RETRY cycle.

BMK2500

– 3000 units

: the unit will Lockout and

Flame Loss During Run

will flash in

the display.

13. Open the manual gas valve closed in step 11.

14. Press the

CLEAR

button. The unit should restart and fire.

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды