Watts Aerco BMK 750 Скачать руководство пользователя страница 19

Страница: 19 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 2: OPERATION

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

157

Engineering Version

Read Only

The Controller’s Engineering software version.

Graphic Data Version

Read Only

The Controller’s graphic version.

Display Version

Read Only

The Controller’s display version.

I/O Board Version

Read Only

The I/O board version.

Touch Version

Read Only

The touch screen version.

Bluetooth Version

Read Only

The Bluetooth version.

Framework Version

Read Only

The Framework version.

Bootloader version

Read Only

The Bootloader version.

Display BL Version

Read Only

Display Bootloader version.

I/O PCB BL Version

Read Only

I/O Board PCB Bootloader version.

2.3.3.6

Main Menu

→

Diagnostics

→

Comm & Network

Main Menu

→

Diagnostics

→

Comm & Network

→

IP Network

Unit IP Address

Read Only

The unit’s IP address.

Subnet Mask

Read Only

The unit’s subnet mask address.

Gateway IP Address

Read Only

The unit’s gateway IP address.

DSN 1

Read Only

The unit’s DSN 1 address.

DSN 2

Read Only

The unit’s DSN 2 address.

Unit MAC Address

Read Only

The unit’s MAC address.

Network Status

Read Only

The unit’s current network status.

Main Menu

→

Diagnostics

→

Comm & Network

→

BAS

BAS

Read Only

The Building Automation System protocol.

Communication
Address

Read Only

The unit’s BAS address.

Device Instance

Read Only

The unit’s Device Instance within BAS.

Unit IP Address

Read Only

The unit’s IP address on the network.

Unit MAC Address

Read Only

The unit’s MAC address within BAS.

Last Command
Received

Read Only

The last command received by the unit.

BAS IP

Read Only

If Security is enabled, this is the IP of the BAS system
that the unit can only communicate with.

Network Status

Read Only

The unit’s BAS network’s current status.

Main Menu

→

Diagnostics

→

Comm & Network

→

onAER

Unit IP Address

Read Only

The unit’s IP address.

Upload Time

Read Only

Frequency at which the unit transmits data to onAER

Test Setup

Enable

Initiates test o onAER functionality.

Test Heartbeat

Enable

Initiates test of the onAER heartbeat.

Main Menu

→

Diagnostics

→

Comm & Network

→

USB Storage

Status

Read Only

Status of the USB device.

Serial Number

Read Only

The serial number of the USB device.

Size

Read Only

The size of the USB device.

Available Space

Read Only

The amount of free space on the USB device.

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды