Watts Aerco BMK 750 Скачать руководство пользователя страница 24

Страница: 24 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 2: OPERATION

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

157

Error Threshold

Numeric Entry

Client/Manager

The number of Modbus Comm errors allowed
before invoking a Modbus comm fault (1 to 9).

Comm Error 1-8

Read Only

Client/Manager

The number of comm errors on ports 1 - 8.

Comm Error 9-16

Read Only

Client/Manager

The number of comm errors on ports 9

– 16..

SSD Address

Numeric Entry

Client/Manager

The Client/Client Device address (0 to 250).

SSD Temp Format

Toggle

Manager

Choose either

Points

Degrees

Time & Date Sync Over
BST

Enable/Disable

Client/Manager

If Enabled, the unit will synchronize time and date
with the BST Manager.

BST Min Units

Numeric Entry

Manager

The minimum number of units in the BST cascade
(1 to 16).

BST Max Units

Numeric Entry

Manager

The maximum number of units in the BST cascade
(1 to 16).

BST On Timeout

Numeric Entry

Manager

Specifies the time the BST Manager must wait for a
backup Client unit to turn on (15

– 300).

Main Menu

→

Advanced Setup

→

BST Cascade

→

BST Application Configuration

Application

Select

The BST

Cascade’s application, either

Other

SH Operating Mode
Other Operating Mode

Select

The BST

Cascade’s operating mode,

Constant Setpoint

SH Setpoint
Other Setpoint

Numeric Entry

The BST

Cascade’s Setpoint

(

Operating Mode

Constant

Setpoint

BST Outdoor Temp

Read Only

The current reading of the outdoor temperature sensor.

Warm Weather Shtdwn

Numeric Entry

The threshold outside temperature above which the unit shuts
down (30 to 120 °F).

Main Menu

→

Advanced Setup

→

BST Cascade

→

Operating Controls

Main Menu

→

Advanced Setup

→

BST Cascade

→

Operating Controls

→

Sequencing Controls

Low Flow Mode

Select

Choose

Off

On - Outlet Temp

On - Avg Temp

. If either

“On” option is chosen, and BST detect a “low-flow” condition, it
slowly shuts down one unit at a time in an attempt to raise the
Fire Rate of the remaining units.

Low Flow Threshold

Numeric Entry

Specifies the valve position below which the plant enters this
mode (10% to 35%).

SH Next On Valve Pos

Numeric Entry

The valve position that triggers the next unit to come on line
(16% to 100%).

SH Next Off Valve Pos

Numeric Entry

The valve position that triggers the next unit to go off line (16%
to 100%).

BST Max Units

Numeric Entry

The maximum number of units that will fire (1 to 16,

Unit Mode

in Cascade Configuration =

BST Manager

SH Valve Close Delay

Numeric Entry

The time an open Isolation Valve will remain open once a unit
cycles off (0 to 15 min.,

Unit Mode

BST Manager

SH BST Fire Rate Up

Numeric Entry

Controls the frequency of updates made to the Fire Rate sent to
all units.

DHW High-Fire Fire Rate

Numeric Entry

Specifies the firing rate above which the swing boiler will be
requested to support the DHW loop application (55 to 90).

Main Menu

→

Advanced Setup

→

BST Cascade

→

Operating Controls

→

Anti-Cycling Control

On Delay

Enter

Minimum length of time a unit must stay off after shutting
down/going standby (30 to 300 sec.).

Slow Shutdown

Enable/Disable

Once enabled, if the unit runs at a fire rate above

Off Delay

Threshold

and then shuts down, the fire rate will be reduced

to the Stop Level for a period of time defined in

Off Delay

Off Delay

Numeric Entry

Specifies the amount of time full shut down will be delayed (0 to
9999 sec.,

Slow Shutdown

Enabled

Off Delay Threshold

Numeric Entry

The threshold fire rate above which

Slow Shutdown

will take

effect (40% to 100%,

Slow Shutdown

Enabled

Shutoff Delay Temp

Numeric Entry

The temperature above setpoint the unit may rise to during
delay shutdown (0°F to 25°F).

Demand Offset

Numeric Entry

Offset temperature from setpoint before a unit may come online
(0°F to 25°F).

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды