Watts Aerco BMK 750 Скачать руководство пользователя страница 153

Страница: 153 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 9

– TROUBLESHOOTING

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

153

157

TABLE 9-1: Boiler Troubleshooting Procedures

Fault

Probable Causes

Corrective Action

Defective Power Supply Board
or fuse.

Check DS1 & DS2 LEDs on Power Supply
Board. If they are not steady ON, replace
Power Supply Board.

Defective IGST Board.

Check “Heartbeat” LED DS1 and verify it is
blinking ON & OFF every second. If not,
replace IGST Board.

PRG
SWTCH
OPEN
DURING
PURGE

Defective Purge

switch.

If the air-fuel valve does rotate, check Purge

switch for continuity when closing. Replace
switch if continuity does not exist.

No voltage present at switch.

Measure for 24 VAC from each side of the
switch to ground. If 24VAC is not present,
refer fault to qualified service personnel.

Switch wired incorrectly.

Check to ensure that the switch is wired
correctly (correct wire numbers on the
normally open terminals).

Defective Power Supply Board
or fuse.

Check DS1 & DS2 LEDs on Power Supply
Board. If they are not steady ON, replace
Power Supply Board.

Defective IGST Board.

Check “Heartbeat” LED DS1 and verify it is
blinking ON & OFF every second. If not,
replace IGST Board.

OUTDOOR
TEMP
SENSOR
FAULT

Loose or broken wiring.

Inspect Outdoor Temperature sensor for loose
or broken wiring.

Defective Sensor.

Check resistance of sensor to determine if it is
within specification.

Incorrect Sensor.

Ensure that the correct sensor is installed.

RECIRC
PUMP
FAILURE

Internal recirculation pump
failed.

1. Replace recirculation pump.

REMOTE
SETPT
SIGNAL
FAULT

Remote setpoint signal not
present:

•

Not yet installed.

•

Wrong polarity.

•

Signal defective at source.

•

Broken or loose wiring.

Check I/O Box to ensure signal is hooked up.

•

Hook up if not installed.

•

If installed, check polarity.

•

Measure signal level.

•

Check continuity of wiring between source
and unit.

Signal is not isolated (floating) if
4 to 20 mA.

Check signal at source to ensure it is isolated.

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды