Watts Aerco BMK 750 Скачать руководство пользователя страница 106

Страница: 106 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 7

– BOILER SEQUENCING TECHNOLOGY

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

106

157

7.1.1

Installation Notes

A ProtoNode is needed for all Protocols on BMK with EDGE[i] Controllers, including BACnet,
Modbus. If your installation includes a ProtoNode SSD (Client-Client Device), you

must

adhere

to the procedure listed below. Failure to complete these steps can result in the failure of the
BST system.

NOT

install the ProtoNode device at the outset of the installation. If the ProtoNode device

is already installed, you must physically disconnect it from the Modbus network on the I/O
board.

Make sure that the Modbus load and bias resistors are properly configured for the system
to operate without the ProtoNode installed.

Temporarily set the BST system for

Constant Setpoint

mode of operation (see below).

Turn on and completely test the installation to verify that it is operating proper.

Once the installation is working properly as a BST system, install the ProtoNode device.

Make sure that the Modbus load and bias resistors are properly configured for the system
to operate with the ProtoNode installed.

Set the BST system for desired mode of operation (

Setpoint

mode).

Test the system completely with the ProtoNode installed.

7.2 BST QUICK START CHART

Select the single option that suites your installation and then complete the instructions in the
corresponding sub-sections of section 7.3

BST Implementation Instructions

Constant Setpoint (choose option 1 or 2)

Option 1

– Direct Wired Header (Header Temp)

Complete section 7.3.1

Option 2

– Modbus Header (Network)

Complete section 7.3.2

Outdoor Reset (choose option 3 or 4)

Option 3

– Direct Wired Header AND Direct Wired Outdoor Air

Complete section 7.3.3

Option 4

– Modbus Header AND Modbus Outdoor Air

Complete section 7.3.4

Remote Setpoint (choose option 5 through 8)

Option 5

– 4-20ma Drive AND Direct Wired Header

Complete section 7.3.5

Option 6

– Modbus Drive AND Direct Wired Header

Complete section 7.3.6

Option 7

– 4-20ma Drive AND Modbus Header

Complete section 7.3.7

Option 8

– Modbus Drive AND Modbus Header

Complete section 7.3.8

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды