Watts Aerco BMK 750 Скачать руководство пользователя страница 87

Страница: 87 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 5

– SAFETY DEVICE TESTING

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

157

5.6.2

Delayed Interlock Test

Delayed Interlock Test Instructions

Remove the cover from the I/O Box and locate the DELAYED INTL’K IN terminals.

2. On the Controller, go to:

Main Menu

→

Diagnostics

→

Manual Mode

, then enable the

Manual Run

control.

3. Set the valve position between 25% and 30% using the

(Plus) and

–

(Minus) controls.

4. If there is a jumper across the

DELAYED INTL’K IN terminals, remove one side of the

jumper. If the interlock is connected to a proving switch of an external device, disconnect
one of the wires leading to the proving switch.

5. The unit should shut down and display a

Delayed Interlock Open

fault message. The

FAULT

LED should be flashing.

6. Reconnect the wire or jumper removed in step 5 to restore the interlock.

7. Press the

CLEAR

button to reset the fault

8. The unit should start.

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды