Watts Aerco BMK 750 Скачать руководство пользователя страница 91

Страница: 91 / 157

Benchmark with Edge [I]: Operation-Maintenance Manual

SECTION 5

– SAFETY DEVICE TESTING

OMM-0145_A99

• GF-218 • 9/18/2019 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page

157

5.8.2

Blocked Inlet Switch Test

This test will be run in simulated fire mode, with the Blocked Inlet switch isolated from the rest of
the control circuitry.

Blocked Inlet Switch Test Instructions

Set the

Controller’s

Enable/Disable

switch to

Disable

Remove the air filter(s) (see Figure 5-6a, 5-6b or 5-6c, above).

WARNING!

The blower suction is very strong and can pull nearby objects into the blower’s fan blades.
Do NOT allow anything to be pulled into the blower! Do not wear anything that could get
caught and pull you into the blower.

Turn off the gas supply ball valve to the boiler and then complete the following steps:

a) Use jumper wires to jump out the Low Gas Pressure switch and the Blower Proof

switch.

b) Remove the black connector boot from the Flame Detector.

c) Create a connector similar to the one shown below and connect it to the Flame

Detector’s black connector boot. Keep the alligator clip away from bare metal parts
until step 4b.

Figure 5-8: Connecting the Flame Signal Generator

On the Controller, go to:

Main Menu

→

Diagnostics

→

Manual Mode

and then put the unit in

Manual

Mode

, then complete the following:

a) Ramp the boiler up to 100% fire rate and then set the Controller

’s

Enable/Disable

switch to

Enable

b) When the Controller gets into the ignition phase, it will show

Ignition Trial

. At that point

attach the alligator clip (see Figure 5-8) to any bare metal surface or ground. The
Controller displays

Flame Proven

and begins to ramp up to 100% fire rate. Note that

no gas or flame is present in the boiler at this time.

Wait for the boiler to ramp up to at least 90% before continuing.

Cover the combustion air inlet opening with a solid, flat object, such as a piece of thick plywood or a
thick metal plate.

The unit should shut down and display

Airflow Fault During Run

. This step confirms proper

operation of the Blocked Inlet switch.

Remove the cover from the air inlet opening and reinstall the Combustion Air Duct or air filter.

Remove the jumper wires installed in step 3 and replace the black connector boot on the Flame
Detector.

10.

Press the

CLEAR

button. The unit should restart.

TO WIRE HARNESS

FLAME DETECTOR
CONNECTOR BOOT

CONNECTOR

Содержание Aerco BMK 750






























































































































































Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды

Watts Aerco BMK 750, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco BMK 750

Отзывы:

Похожие инструкции для Aerco BMK 750

Бренды по названию

Популярные бренды