manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

DI5O6-02

N06218

CRUISE MAIN Indicator Light

BE4034

Indicator Light

1.5 sec.

0.5 sec.

ON

OFF

N06219

TC

E1

DLC1

-

DIAGNOSTICS

CRUISE CONTROL SYSTEM

DI-28

6

1996 LAND CRUISER  (RM451U)

PRE-CHECK

1.

DIAGNOSIS SYSTEM

(a)

Check the indicator.
(1)

Turn the ignition switch to ON.

(2)

Check that the CRUISE MAIN indicator light comes
on when the cruise control main switch is turned on,
and that the indicator light goes off when the main
switch is turned OFF.

HINT:
If the indicator check result is not normal, proceed to trouble-
shooting (See page 

BE-34

) for the combination meter section.

(b)

Check the DTC.

HINT:
If a malfunction occurs in the No. 1 vehicle speed sensors or ac-
tuator, etc. during cruise control driving, the ECU actuates
AUTO CANCEL of the cruise control and turns on and off the
CRUISE MAIN indicator light to inform the driver of a malfunc-
tion. At the same time, the malfunction is stopped in memory as
a diagnostic trouble code.

(c)

Output of DTC using diagnosis check wire.
(1)

Turn the ignition switch ON.

(2)

Using SST, connect terminals Tc and E

1 

of DLC1.

SST

09843-18020

(3)

Read the DTC on the CRUISE MAIN indicator light.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Yakima KingJoe 2 Quick Start Manual preview
KingJoe 2
Бренд: Yakima Страницы: 7
Yakima BowDown Quick Start Manual preview
BowDown
Бренд: Yakima Страницы: 6
Yakima LOCKN'LOAD Manual preview
LOCKN'LOAD
Бренд: Yakima Страницы: 10
Yakima HitchSki Quick Start Manual preview
HitchSki
Бренд: Yakima Страницы: 12
Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Бренд: Bimmer Jakes Страницы: 4
AutoWatch 457 Rli Wiring Diagram preview
457 Rli
Бренд: AutoWatch Страницы: 4
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Бренд: Oldsmobile Страницы: 380
Mazda 0000-8L-G03A Installation Instructions preview
0000-8L-G03A
Бренд: Mazda Страницы: 3
Billien OBU 5050 Quick Installation Manual preview
OBU 5050
Бренд: Billien Страницы: 2
Lexus ES 2021 Quick Manual preview
ES 2021
Бренд: Lexus Страницы: 28
Mobridge DA-G2 MOST150 Manual preview
DA-G2 MOST150
Бренд: Mobridge Страницы: 20
Rigid Hitch BULL BAR Installation Instructions preview
BULL BAR
Бренд: Rigid Hitch Страницы: 2
Suzuki SX4 2016 Owner'S Manual preview
SX4 2016
Бренд: Suzuki Страницы: 504
Tobe EPS-LD SafePark Technical Data preview
EPS-LD SafePark
Бренд: Tobe Страницы: 2
DRAGONFIRE 11-0800 Installation Instructions preview
11-0800
Бренд: DRAGONFIRE Страницы: 4
Federal Signal Corporation HighLighter Installation And Programming preview
HighLighter
Бренд: Federal Signal Corporation Страницы: 20
Easee Base 1-Way User Manual / Installation Manual preview
Base 1-Way
Бренд: Easee Страницы: 21
BMW 325i 1991 Electrical Troubleshooting Manual preview
325i 1991
Бренд: BMW Страницы: 64

Бренды по названию

Популярные бренды

Загрузить еще бренды