manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

A00164

P03792

P22893

DI

−

56

−

DIAGNOSTICS

ENGINE

1996 LAND CRUISER   (RM451U)

INSPECTION PROCEDURE

1

Check spark plug and spark of misfiring cylinder.

PREPARATION:

(a)

Remove No.2 and No.3 cylinder head cover.

(b)

Disconnect the high

−

tension cord from spark plug.

(c)

Remove spark plug.

CHECK:

(a)

Check the carbon deposits on electrode.

(b)

Check electrode gap.

OK:

(1) No large carbon deposit present.
Not wet with gasoline or oil.
(2) Electrode gap: 0.8 mm (0.031 in.).

PREPARATION:

(a)

Install the spark plug to the high

−

tension cord.

(b)

Ground the spark plug.

(c)

Disconnect injector connector.

CHECK:

Check if spark occurs while engine is being cranked.

NOTICE:
To prevent excess fuel being injected from the injectors
during this test, don’t crank the engine for more than 5 

−

 10

seconds at a time.
OK:

Spark jumps across electrode gap.

NG

Replace or check ignition system (See page

IG

−

1

).

OK

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

KC HiLiTES C Series Wiring Diagram preview
C Series
Бренд: KC HiLiTES Страницы: 4
Davis Instruments 8127 Installation Instructions Manual preview
8127
Бренд: Davis Instruments Страницы: 16
Baja Designs S8 Instructions Manual preview
S8
Бренд: Baja Designs Страницы: 6
Yakima K800 Instructions Manual preview
K800
Бренд: Yakima Страницы: 8
Kia Picanto 2015 Quick Reference Manual preview
Picanto 2015
Бренд: Kia Страницы: 10
walser 30968 User Instructions preview
30968
Бренд: walser Страницы: 24
Whispbar K607W Fitting Instructions Manual preview
K607W
Бренд: Whispbar Страницы: 14
Qeedon Higlow Series Product Instruction preview
Higlow Series
Бренд: Qeedon Страницы: 2
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Бренд: Thule Страницы: 12
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Бренд: Mitsubishi Страницы: 362
Whispbar K481W Fitting Instructions Manual preview
K481W
Бренд: Whispbar Страницы: 14
Ford 1999 Crown Victoria Owner'S Manual preview
1999 Crown Victoria
Бренд: Ford Страницы: 208
Edelbrock 67312 Installation Instructions preview
67312
Бренд: Edelbrock Страницы: 2
Edelbrock 3824 Installation Instructions preview
3824
Бренд: Edelbrock Страницы: 2
Kia 2015 Soul Features & Functions Manual preview
2015 Soul
Бренд: Kia Страницы: 46
Chrysler DODGE AD100 1993 Service Manual preview
DODGE AD100 1993
Бренд: Chrysler Страницы: 1502
Honda 2005 Civic Owner'S Manual preview
2005 Civic
Бренд: Honda Страницы: 234
Blue Ox BX2711 Installation Instructions Manual preview
BX2711
Бренд: Blue Ox Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды