manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

P03789

P08374

A16075

1 Dot Mark

EM

−

60

−

ENGINE MECHANICAL

CYLINDER HEAD

1996 LAND CRUISER   (RM451U)

10. INSTALL SEMI

−

CIRCULAR PLUG

(a)

Remove any old packing (FIPG) material.

(b)

Apply seal packing to the cylinder head installation sur-
face of the semi

−

circular plug.

Seal packing: Part No. 08826

−

00080 or equivalent

(c)

Install the semi

−

circular plug to the cylinder head.

11.

SET NO. 1 CYLINDER TO TDC/COMPRESSION

(a)

Turn the crankshaft pulley, and align its groove with the
timing mark ”0” of the timing chain cover.

(b)

Check that the timing marks with 1 and 2 dots are in
straight line on the cylinder head surface as shown in the
illustration.

If not, turn the crankshaft 1 revolution (360

°

) and align the mark

as above.

12. INSTALL CYLINDER HEAD COVER

(a)

Install the gasket to the cylinder head cover.

(b)

Install the cylinder head cover with the 13 bolts.

13. INSTALL WATER BYPASS OUTLET AND PIPE

(a)

Install a new O

−

ring to the water bypass outlet.

(b)

Install 2 new O

−

rings to the water bypass pipe.

(c)

Apply soapy water to the O

−

rings.

(d)

Assemble the water bypass outlet and pipe.

(e)

Install the water bypass outlet and pipe with the 2 bolts.

Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

ZAPTEC Go Quick Manual preview
Go
Бренд: ZAPTEC Страницы: 64
ZAPTEC Go Installation Manual preview
Go
Бренд: ZAPTEC Страницы: 24
Dakota Digital VHX-37F Installation preview
VHX-37F
Бренд: Dakota Digital Страницы: 2
Dakota Digital BIM-01-2 Manual preview
BIM-01-2
Бренд: Dakota Digital Страницы: 7
Jeep 2009 Wrangler Quick Reference Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 12
Jeep 2008 Liberty Installation Instructions Manual preview
2008 Liberty
Бренд: Jeep Страницы: 6
Fabbri BICI OK 2 Quick Start Manual preview
BICI OK 2
Бренд: Fabbri Страницы: 4
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Бренд: Toyota Страницы: 19
Edelbrock 6883 Instructions preview
6883
Бренд: Edelbrock Страницы: 2
Yuasa SmartShot Automatic 12V 1.5 Amp 5 Stage Technical Manual preview
SmartShot Automatic 12V 1.5 Amp 5 Stage
Бренд: Yuasa Страницы: 44
AC Schnitzer X3 M-Technik Fitting Instructions Manual preview
X3 M-Technik
Бренд: AC Schnitzer Страницы: 20
GMC Envoy XUV 2004 Getting To Know Manual preview
Envoy XUV 2004
Бренд: GMC Страницы: 20
Hella AREIA 7040 Installation Instructions Manual preview
AREIA 7040
Бренд: Hella Страницы: 21
Hank HKWP1100-10Q User Quick Manual preview
HKWP1100-10Q
Бренд: Hank Страницы: 2
Whispbar K951W Fitting Instructions For Basic Carrier preview
K951W
Бренд: Whispbar Страницы: 15
Saab 32 025 603 Installation Instructions Manual preview
32 025 603
Бренд: Saab Страницы: 15
National Cycle Quantum Wash'n'Wipe N30208 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30208
Бренд: National Cycle Страницы: 12
Ultraplast MD19 User Manual preview
MD19
Бренд: Ultraplast Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды