manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

TR0BI

−

01

Q00530

Q08384

Q02549

Q07138

TR

−

30

−

TRANSFER

REAR EXTENSION HOUSING

1996 LAND CRUISER   (RM451U)

DISASSEMBLY

1.

REMOVE OIL PUMP DRIVE SHAFT

2.

REMOVE OIL PUMP COVER

(a)

Using a torx socket wrench (T30), remove the 3 screws.

(b)

Install the 2 suitable bolts to the pump cover.

(c)

Remove the pump cover from the rear extension
housing.

3.

REMOVE DRIVE ROTOR FROM DRIVEN ROTOR

4.

REMOVE DRIVEN ROTOR FROM REAR EXTENSION
HOUSING

5.

REMOVE SCREW PLUG, SPRING, BALL AND VALVE
SEAT

(a)

Using a hexagon wrench, remove the screw plug.

(b)

Using a magnetic finger, remove the spring, ball and valve
seat from the rear extension housing.

6.

REMOVE CENTER DIFFERENTIAL CONTROL COU-
PLING ASSEMBLY

(a)

Using a snap ring expander, remove the snap ring.

(b)

Remove the coupling assembly from the rear extension
housing.

7.

REMOVE SEPARATOR AND OIL PUMP PLATE

Remove the 3 bolts, separator and oil pump plate.

8.

REMOVE VEHICLE SPEED SENSOR DRIVE GEAR

(a)

Using a snap ring expander, remove the snap ring.

(b)

Remove the vehicle speed sensor drive gear.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Accel 2020 Installation Instructions preview
2020
Бренд: Accel Страницы: 2
Lancia THESIS CONNECT Owner'S Handbook Manual preview
THESIS CONNECT
Бренд: Lancia Страницы: 386
Safe Fleet PRIME DESIGN VCR 326 Assembly Instructions Manual preview
PRIME DESIGN VCR 326
Бренд: Safe Fleet Страницы: 16
Safe Fleet Prime Design VBC PC11 Quick Start Manual preview
Prime Design VBC PC11
Бренд: Safe Fleet Страницы: 8
Safe Fleet Prime Design AR1418 Manual preview
Prime Design AR1418
Бренд: Safe Fleet Страницы: 4
Front Runner Easy-Out Fitting Instructions preview
Easy-Out
Бренд: Front Runner Страницы: 5
Ford 2004 Freestar Workshop Manual preview
2004 Freestar
Бренд: Ford Страницы: 8
Intec CVD500LCD Installation And Operation Manual preview
CVD500LCD
Бренд: Intec Страницы: 16
Nav TV Ford 4” UNI-CAM Manual preview
Ford 4” UNI-CAM
Бренд: Nav TV Страницы: 6
Saab 2007 9-3 Remote Starter Owner'S Manual preview
2007 9-3 Remote Starter
Бренд: Saab Страницы: 304
Meta System 900000358 Installation Technical Sheet preview
900000358
Бренд: Meta System Страницы: 22
JKS JKSOGS960 Installation Instructions Manual preview
JKSOGS960
Бренд: JKS Страницы: 6
Bestop Bikini Installation Instructions preview
Bikini
Бренд: Bestop Страницы: 5
PowerMadd Tri-mount Installation Instructions preview
Tri-mount
Бренд: PowerMadd Страницы: 3
ECS FIA-030-B Fitting Instructions preview
FIA-030-B
Бренд: ECS Страницы: 4
Whispbar WB751 Manual preview
WB751
Бренд: Whispbar Страницы: 15
Jaeger 12160509J Fitting Instructions Manual preview
12160509J
Бренд: Jaeger Страницы: 16
Phonocar VM 320 Instruction Manual preview
VM 320
Бренд: Phonocar Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды