Toyota 1996 LAND CRUISER Скачать руководство пользователя страница 857

Страница: 857 / 1381

−

ENGINE MECHANICAL

ENGINE UNIT

−

1996 LAND CRUISER (RM451U)

(g)

Disconnect the 3 connectors.

(h)

Remove the 10 bolts and the transfer shift lever boot and
transmission shift lever assembly.

(i)

Pull out the pin and disconnect the shift rod.

(j)

Remove the 4 bolts, hose clamp and the transfer shift le-
ver.

26. REMOVE FRONT EXHAUST PIPE

(a)

Disconnect the heated oxygen sensor connector.

(b)

Remove the 2 nuts and 2 bolts holding the front exhaust
pipe to the rear TWC.

(c)

Disconnect the front exhaust pipe, and remove the gas-
ket.

(d)

Loosen the clamp bolt and disconnect the clamp from the
No.1 support bracket.

(e)

Remove the 2 bolts and No. 1 support bracket.

(f)

Remove the 4 nuts, front exhaust pipe and 2 gaskets.

27. DISCONNECT GROUND STRAP FROM HEAT INSULA-

TOR

28. PLACE JACK UNDER TRANSMISSION

Be sure to put a wooden block between the jack and the trans-
mission oil pan to prevent damage.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1996 LAND CRUISER

Отзывы:

Похожие инструкции для 1996 LAND CRUISER

Бренды по названию

Популярные бренды

Toyota 1996 LAND CRUISER, Руководство пользователя

Результаты поиска

Содержание 1996 LAND CRUISER

Отзывы:

Похожие инструкции для 1996 LAND CRUISER

Бренды по названию

Популярные бренды