manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

SF1ED

−

04

−

SFI

SFI SYSTEM

SF

−

1

629

Author:

Date:

1996 LAND CRUISER   (RM451U)

SFI SYSTEM

PRECAUTION

1.

BEFORE WORKING ON FUEL SYSTEM, DISCON-
NECT NEGATIVE (

−

) TERMINAL CABLE FROM THE

BATTERY.

HINT:
Any diagnostic trouble code retained by the computer will be
erased when the negative (

−

) terminal cable is disconnected.

Therefore, if necessary, read the diagnosis before disconnect-
ing the negative (

−

) terminal cable from the battery.

2.

DO NOT SMOKE OR WORK NEAR AN OPEN FLAME
WHEN WORKING ON FUEL SYSTEM.

3.

KEEP GASOLINE AWAY FROM RUBBER OR LEATH-
ER PARTS

4.

MAINTENANCE PRECAUTIONS

(a)

In event of engine misfire, these precautions should be
taken.
(1)

Check proper connection of battery terminals, etc.

(2)

Handle high

−

tension cords carefully.

(3)

After repair work, check that the ignition coil termi-
nals and all other ignition system lines are recon-
nected securely.

(4)

When cleaning the engine compartment, be espe-
cially careful to protect the electrical system from
water.

(b)

Precautions when handling the oxygen sensor.
(1)

Do not allow the oxygen sensor to drop or hit
against an object.

(2)

Do not allow the sensor to come in contact with wa-
ter.

5.

IF VEHICLE IS EQUIPPED WITH MOBILE RA-
DIO SYSTEM  (HAM, CB, ETC.)

If the vehicle is equipped with a mobile communication system,
refer to the precaution in the IN section.

6.

AIR INDUCTION SYSTEM

(a)

Separation of the engine oil dipstick, oil filler cap, PCV
hose, etc. may cause the engine to run out of tune.

(b)

Disconnection, looseness or cracks in the parts of the air
induction system between the throttle body and cylinder
head will allow air suction and cause the engine to run out
of tune.

7.

ELECTRONIC CONTROL SYSTEM

(a)

Before removing SFI wiring connectors, terminals, etc.,
first disconnect the power by either turning the ignition
switch OFF or disconnecting the negative (

−

) terminal

cable from the battery.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Mazda 2011 Tribute Brochure & Specs preview
2011 Tribute
Бренд: Mazda Страницы: 4
Harbor Freight Tools 92043 Assembly And Operating Instructions preview
92043
Бренд: Harbor Freight Tools Страницы: 4
Kia 2011 optima Owner'S Manual preview
2011 optima
Бренд: Kia Страницы: 385
Daewoo RACER 1998 Electrical Wiring Diagram preview
RACER 1998
Бренд: Daewoo Страницы: 68
Hyundai Getz 2004 Owner'S Manual preview
Getz 2004
Бренд: Hyundai Страницы: 437
TATA Motors nano genX Owner'S Manual preview
nano genX
Бренд: TATA Motors Страницы: 156
Safe Fleet RVS-218627 Instruction Manual preview
RVS-218627
Бренд: Safe Fleet Страницы: 38
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Бренд: B-Speech Страницы: 24
BURY CC 9040 Specification preview
CC 9040
Бренд: BURY Страницы: 2
Honda 2010 Pilot Technology Reference Manual preview
2010 Pilot
Бренд: Honda Страницы: 20
Kia 2009 Rio Series Owner'S Manual preview
2009 Rio Series
Бренд: Kia Страницы: 219
Hyundai Santa Fe 2019 Getting Started Manual preview
Santa Fe 2019
Бренд: Hyundai Страницы: 18
Reese Explore 63153 Instruction Manual preview
63153
Бренд: Reese Explore Страницы: 9
INDIWORK A-LINK2-NTG5 Instruction Manual preview
A-LINK2-NTG5
Бренд: INDIWORK Страницы: 18
Opel CORSA 2020 Infotainment Manual preview
CORSA 2020
Бренд: Opel Страницы: 103
Scosche HUD580GC Manual preview
HUD580GC
Бренд: Scosche Страницы: 12
CARFACE CF145962E Instruction Manual preview
CF145962E
Бренд: CARFACE Страницы: 16
LaserLine 921K Operating Instructions preview
921K
Бренд: LaserLine Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды