manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

TF0969

SST

TF0958

Q07138

Q02549

Q08384

TR

−

34

−

TRANSFER

REAR EXTENSION HOUSING

1996 LAND CRUISER   (RM451U)

4.

INSTALL REAR OUTPUT SHAFT

(a)

Using SST and a press, install the rear output shaft.
SST

09316

−

20011, 09316

−

60011 (09316

−

00011,

09316

−

00031)

(b)

Install the 2 seal rings to the rear output shaft.

(c)

Select a snap ring that will allow minimum axial play.

Mark

Thickness    mm (in.)

1

1.95 (0.0768)

2

2.05 (0.0807)

3

2.15 (0.0847)

4

2.25 (0.0886)

(d)

Using a snap ring expander, install a new snap ring.

5.

INSTALL VEHICLE SPEED SENSOR DRIVE GEAR

(a)

Install the vehicle speed sensor drive gear.

(b)

Using a snap ring expander, install the snap ring.

6.

INSTALL OIL PUMP PLATE AND SEPARATOR

(a)

Install the oil pump plate.

(b)

Install the separator.

(c)

Install and torque the 3 bolts.

Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)

7.

INSTALL CENTER DIFFERENTIAL CONTROL COU-
PLING ASSEMBLY

(a)

Install the coupling assembly to the output shaft.

(b)

Using a snap ring expander, install the snap ring.

8.

INSTALL VALVE SEAT, BALL, SPRING AND SCREW
PLUG

(a)

Apply gear oil to the ball.

(b)

Install the valve seat, ball and spring.

(c)

Apply liquid sealer to the screw plug.

Sealant: Part No. 08833

−

00080, THREE BOND 1344,

LOCTITE 242 or equivalent

(d)

Using a hexagon wrench, install and torque the screw
plug.

Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Paccar DAF POWERCHOICE 250A Installation Manual preview
DAF POWERCHOICE 250A
Бренд: Paccar Страницы: 20
Whispbar K925W Fitting Instructions Manual preview
K925W
Бренд: Whispbar Страницы: 15
Audi Q3 2015 - 2019 Technical Service Bulletin preview
Q3 2015 - 2019
Бренд: Audi Страницы: 12
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Бренд: Wagan Страницы: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Бренд: Chevrolet Страницы: 50
Camoplast Polaris TATOU 4S Installation Manuallines preview
Polaris TATOU 4S
Бренд: Camoplast Страницы: 13
Big Mikes Performance Parts STO N SHO SNS 144 Installation Procedures Manual preview
STO N SHO SNS 144
Бренд: Big Mikes Performance Parts Страницы: 7
Lincoln MKZ 2018 Quick Reference Manual preview
MKZ 2018
Бренд: Lincoln Страницы: 10
Belkin F8V9017 User Manual preview
F8V9017
Бренд: Belkin Страницы: 2
Tesla MODEL Y Owner'S Manual preview
MODEL Y
Бренд: Tesla Страницы: 274
TATA Motors Indigo eCS Owner'S Manual & Service Book preview
Indigo eCS
Бренд: TATA Motors Страницы: 166
Advanced Diagnostics MVP PRO Manual preview
MVP PRO
Бренд: Advanced Diagnostics Страницы: 10
TOPPOINT LT95090 Quick Start Manual preview
LT95090
Бренд: TOPPOINT Страницы: 2
Cadillac XLR-V Specifications preview
XLR-V
Бренд: Cadillac Страницы: 2
Buick Cascada 2016 Getting To Know Manual preview
Cascada 2016
Бренд: Buick Страницы: 20
QA1 GS501 Installation Instructions preview
GS501
Бренд: QA1 Страницы: 3
Car-Interface CI-RL4-MM-NP Manual preview
CI-RL4-MM-NP
Бренд: Car-Interface Страницы: 23
Prorack K349 Fitting Instructions Manual preview
K349
Бренд: Prorack Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды