manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

BR1DA

−

01

BR

−

44

−

BRAKE

PARKING BRAKE

1996 LAND CRUISER   (RM451U)

REASSEMBLY

Reassembly is in the reverse order of disassembly (See
page 

BR

−

40

).

NOTICE:
Apply high temperature grease and lithium soap base gly-
col grease to the parts indicated by the arrows (See page

BR

−

39

).

1.

ADJUST PARKING BRAKE SHOE CLEARANCE

(a)

Disconnect the PKB cable from bellcrank and remove the
2 tension springs.

(b)

Loosen the stopper bolt.

(c)

Temporarily install the hub nuts.

(d)

Remove the hole plug.

(e)

Turn the adjuster and expand the shoes until the disc
locks.

(f)

Return the adjuster 8 notches.

(g)

Install the hole plug.

2.

ADJUST BELLCRANK

(a)

Pull the bellcrank until all play in the interior linkage is tak-
en up.

(b)

Screw in the bellcrank adjusting bolt to where it contacts
on the dust seal.

(c)

Loosen it one turn, and lock it at that position with the lock
nut.

Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)

(d)

Install the bellcrank spring.

(e)

Connect the PKB cable to the bellcrank.

3.

BEDDING DOWN PARKING BRAKE SHOES AND
DISC

(a)

Drive the vehicle at about 50 km/h (31 mph) on a safe, lev-
el and dry road.

(b)

With the parking brake release button pushed in, pull on
the lever with 88 N (9 kgf, 19.8 lbf) of force.

(c)

Drive the vehicle for about 400 meters (0.25 mile) in this
condition.

(d)

Repeat this procedure 2 or 3 times.

4.

RECHECK AND ADJUST PARKING BRAKE LEVER
TRAVEL

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

iDataLink ADS-ALCA Install Manuals preview
ADS-ALCA
Бренд: iDataLink Страницы: 30
Warrior Products 4560 Manual preview
4560
Бренд: Warrior Products Страницы: 4
Subaru 2016 Outback Owner'S Manual preview
2016 Outback
Бренд: Subaru Страницы: 99
Pontiac 2004 Vibe Navigation System Owner'S Manual preview
2004 Vibe Navigation System
Бренд: Pontiac Страницы: 44
MASCOT SMARTCHARGER User Manual preview
SMARTCHARGER
Бренд: MASCOT Страницы: 12
Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne... Installation Instructions preview
LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...
Бренд: Dakota Digital Страницы: 3
Safe Fleet RVS systems RVS-M641 Instruction Manual preview
RVS systems RVS-M641
Бренд: Safe Fleet Страницы: 24
WABCO TP19039 Manual preview
TP19039
Бренд: WABCO Страницы: 34
Acura 2011 RDX Navigation System Advanced Technology Manual preview
2011 RDX Navigation System
Бренд: Acura Страницы: 16
Curt Group 60638 Installation Manual preview
60638
Бренд: Curt Group Страницы: 3
Juna JRDAB-03 Installation Manual preview
JRDAB-03
Бренд: Juna Страницы: 10
SMART EQ forfour 2018 Owner'S Manual preview
EQ forfour 2018
Бренд: SMART Страницы: 224
FIRRAK FIRRAK arca Assembly Instructions Manual preview
FIRRAK arca
Бренд: FIRRAK Страницы: 12
Metra Electronics 99-6510 User Manual preview
99-6510
Бренд: Metra Electronics Страницы: 17
Kia 2015 Soul Features & Functions Manual preview
2015 Soul
Бренд: Kia Страницы: 46
ABB InCharge Terra AL2-40-240-T1-WC1R Installation Manual preview
InCharge Terra AL2-40-240-T1-WC1R
Бренд: ABB Страницы: 39
Chevrolet 2003 Cavalier Owner'S Manual preview
2003 Cavalier
Бренд: Chevrolet Страницы: 362
Chevrolet 2002 Venture Owner'S Manual preview
2002 Venture
Бренд: Chevrolet Страницы: 486

Бренды по названию

Популярные бренды

Загрузить еще бренды