manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

EM1EE

−

02

EM

−

76

−

ENGINE MECHANICAL

ENGINE UNIT

1996 LAND CRUISER   (RM451U)

INSTALLATION

1.

CHECK TORQUE CONVERTER CLUTCH INSTALLA-
TION

Using calipers and straight edge, measure from the installed
surface of the torque converter clutch to the front surface of the
transmission.

Correct distance: 15.7 mm (0.618 in.) or more

If the distance is less than the specifications, check for an im-
proper installation.

2.

INSTALL TRANSMISSION TO ENGINE

Install the transmission with the 7 bolts.

Torque: 72 N·m (730 kgf·cm, 53 ft·lbf)

3.

INSTALL TORQUE CONVERTER CLUTCH MOUNTING
BOLTS

Install the 6 bolts by turning the crankshaft.

Torque: 55 N·m (550 kgf·cm, 41 ft·lbf)

HINT:
First install the green colored bolt and then the remaining 5
bolts.

4.

INSTALL HOLE PLUG

5.

CONNECT THROTTLE CABLE TO THROTTLE BODY

6.

INSTALL A/T OIL COOLER PIPES FOR TRANSMIS-
SION

(a)

Temporarily install the 3 mounting bolts.

(b)

Connect the 2 oil cooler pipes to the unions on the trans-
mission. Tighten the union nuts.

Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)

(c)

Tighten the 3 clamp mounting bolts.

7.

INSTALL STARTER

(a)

Install the starter with the 2 bolts.

Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)

(b)

Connect the starter connector.

8.

CONNECT ENGINE WIRE TO TRANSMISSION

(a)

Connect the 2 connectors from the transmission.

(b)

Connect the PNP switch connector.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Mazda 2011 Tribute Brochure & Specs preview
2011 Tribute
Бренд: Mazda Страницы: 4
Napoli NPL-TV 7874 DIGITAL Instruction Manual preview
NPL-TV 7874 DIGITAL
Бренд: Napoli Страницы: 20
PullRite 20K OE Series Installation Instructions Manual preview
20K OE Series
Бренд: PullRite Страницы: 10
Cadillac 2007 CTS Owner'S Manual preview
2007 CTS
Бренд: Cadillac Страницы: 518
Opel OPEL INSIGNIA Infotainment Manual preview
OPEL INSIGNIA
Бренд: Opel Страницы: 141
BendPak Autostacker PL-6SR Installation And Operation Manual preview
Autostacker PL-6SR
Бренд: BendPak Страницы: 104
Quadratec 12057.0263 Installation Manual preview
12057.0263
Бренд: Quadratec Страницы: 12
Meta System 900000358 Installation Technical Sheet preview
900000358
Бренд: Meta System Страницы: 22
Subaru Legacy 2011 Quick Reference Manual preview
Legacy 2011
Бренд: Subaru Страницы: 19
r.LiNK RL2-NBT Manual preview
RL2-NBT
Бренд: r.LiNK Страницы: 20
newmotion Dynamic Power Management Home - Module Installation Instruction preview
Dynamic Power Management Home - Module
Бренд: newmotion Страницы: 20
AutoLoc SB3PR Series User Manual And Installation Manual preview
SB3PR Series
Бренд: AutoLoc Страницы: 6
Saab 32 025 907 Installation Instructions Manual preview
32 025 907
Бренд: Saab Страницы: 37
CITROEN CX 2000 Repair Manual preview
CX 2000
Бренд: CITROEN Страницы: 394
Bowers & Wilkins Turnoverball 1020 Installation Instructions Manual preview
Turnoverball 1020
Бренд: Bowers & Wilkins Страницы: 6
Volvo XC40 RECHARGE Retailer Pairing Manual preview
XC40 RECHARGE
Бренд: Volvo Страницы: 5
Ford 2007 Transit Owner'S Handbook Manual preview
2007 Transit
Бренд: Ford Страницы: 46
PAC RP4-CH11 Instruction Manual preview
RP4-CH11
Бренд: PAC Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды