Toyota 1996 LAND CRUISER Скачать руководство пользователя страница 308

Страница: 308 / 1381

BO4033

BO392

−

BODY

SLIDING ROOF

−

1996 LAND CRUISER (RM451U)

ADJUSTMENT

REMOVE SLIDING ROOF GARNISHES

Before making adjustments, remove the left and right sliding
roof garnishes.
HINT:
After adjustment, reinstall the sliding roof garnishes.

ADJUST LEVEL DIFFERENCE

Adjust by increasing or decreasing the number of shims be-
tween the bracket and sliding roof.

ADJUST FORWARD OR REARWARD

(a)

Adjust by loosening the sliding roof installation nuts, and
move the sliding roof bracket forwards and backwards.

(b)

When the front or rear alignment is not correct, remove
the glass and adjust the drive rail.

(c)

Using a screwdriver, slide the link forwards or backwards
to align the 2 marks, as shown in the illustration.

(d)

Slide the bracket to the forefront with your hand.

ADJUST RIGHT OR LEFT

Adjust by loosening the sliding roof rear shoe installation nuts,
and move the sliding roof to the right and left.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1996 LAND CRUISER

Отзывы:

Похожие инструкции для 1996 LAND CRUISER

Бренды по названию

Популярные бренды

Toyota 1996 LAND CRUISER, Руководство пользователя

Результаты поиска

Содержание 1996 LAND CRUISER

Отзывы:

Похожие инструкции для 1996 LAND CRUISER

Бренды по названию

Популярные бренды