manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

SR16O

−

01

Z14503

Dial Indicator

30 mm

(1.18 in.)

Z14504

Dial Indicator

Z10600

Z06211

SR

−

38

−

STEERING

POWER STEERING GEAR

1996 LAND CRUISER   (RM451U)

INSPECTION

NOTICE:
When using a vise, do not overtighten it.
1.

INSPECT BALL CLEARANCE

Using a dial indicator, check the ball clearance. Move the worm
gear up and down.

Maximum clearance: 0.15 mm (0.0059 in.)

2.

INSPECT CROSS SHAFT ADJUSTING SCREW
THRUST CLEARANCE

Using a dial indicator, measure the thrust clearance.

Standard clearance: 0.03 

−

 0.05 (0.0012 

−

 0.0020 in.)

3.

IF NECESSARY, ADJUST CROSS SHAFT ADJUSTING
SCREW THRUST CLEARANCE

(a)

Using a chisel and hammer, unstake the No.1 lock nut.

(b)

Using SST, remove the No.1 lock nut.
SST

09630

−

00014 (09631

−

00051)

(c)

Using a screwdriver, adjust the adjusting screw for correct
thrust clearance.

(d)

Using the SST, tighten a new lock nut.

(e)

Using a chisel and hammer, stake the lock nut.

4.

IF NECESSARY, REPLACE OIL SEAL, METAL
SPACER AND TEFLON RING

(a)

Using a screwdriver, pry out the oil seal from the gear
housing.

(b)

Using snap ring pliers, remove the snap ring from the gear
housing.

(c)

Remove the metal spacer, teflon ring and O

−

ring from the

gear housing.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Suzuki SX4 SEDAN 2008 Owner'S Manual preview
SX4 SEDAN 2008
Бренд: Suzuki Страницы: 16
Back View RV-250 User Manual preview
RV-250
Бренд: Back View Страницы: 168
Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Бренд: Toyota Страницы: 529
RAM 2015 1500 User Manual preview
2015 1500
Бренд: RAM Страницы: 292
RAM Trucks 1500 User Manual preview
Trucks 1500
Бренд: RAM Страницы: 116
RAM 2500 2020 Quick Reference Manual preview
2500 2020
Бренд: RAM Страницы: 20
Axxess AX-DSPX-HYKIA2 Installation Instructions preview
AX-DSPX-HYKIA2
Бренд: Axxess Страницы: 4
Vintage Air 473275 Manual preview
473275
Бренд: Vintage Air Страницы: 14
Yescom YES5062 User Manual preview
YES5062
Бренд: Yescom Страницы: 4
Z Automotive Tazer DT User Manual preview
Tazer DT
Бренд: Z Automotive Страницы: 16
Uebler X21 nano Mounting And Operating Instructions preview
X21 nano
Бренд: Uebler Страницы: 56
Audiovox UniStreamONE Installation Manual preview
UniStreamONE
Бренд: Audiovox Страницы: 24
Mercedes-Benz GLE Coupe Brief Overview preview
GLE Coupe
Бренд: Mercedes-Benz Страницы: 2
Westin 25-0560 Instructions preview
25-0560
Бренд: Westin Страницы: 2
Dodge Challenger 2013 Owner'S Manual preview
Challenger 2013
Бренд: Dodge Страницы: 543
ULTIMATE SPEED 304669 Instructions For Use And Safety Manuallines preview
304669
Бренд: ULTIMATE SPEED Страницы: 50
Safe Fleet PRIME DESIGN HRR-369-E-UM3-96 Manual preview
PRIME DESIGN HRR-369-E-UM3-96
Бренд: Safe Fleet Страницы: 12
Kocchi's 772161M1 Manual preview
772161M1
Бренд: Kocchi's Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды