manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

EM0281

P03976

P03977

−

ENGINE MECHANICAL

CYLINDER HEAD

EM

−

45

1996 LAND CRUISER   (RM451U)

(c)

Using a spring tester, measure the tension of the valve
spring at the specified installed length.

Installed tension:
214 

−

 238 N (21.8 

−

 24.2 kgf, 48.1 

−

 53.4 lbf)

at 36.5 mm (1.437 in.)

If the installed tension is not as specified, replace the valve
spring.

9.

INSPECT CAMSHAFTS

(a)

Inspect for runout.
(1)

Place the camshaft on V

−

blocks.

(2)

Using a dial indicator, measure the circle runout at
the center journal.

Maximum circle runout: 0.06 mm (0.0024 in.)

If the circle runout is greater than maximum, replace the cam-
shaft.

(b)

Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.

Standard cam lobe height:
50.61 

−

 50.71 mm (1.9925 

−

 1.9965 in.)

Minimum cam lobe height: 50.51 mm (1.9886 in.)

If the cam lobe height is less than minimum, replace the cam-
shaft.

(c)

Inspect the journals.
Using a micrometer, measure the journal diameter.

Journal diameter: 
26.959 

−

 26.975 mm (1.0614 

−

 1.0620 in.)

If the journal diameter is not as specified, check the oil clear-
ance.

(d)

Inspect the camshaft bearings.
Check that bearings for flaking and scoring.

If the bearings are damaged, replace the bearing caps and cyl-
inder head as a set.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

ABL eMH1 WALLBOX Manual preview
eMH1 WALLBOX
Бренд: ABL Страницы: 176
ABL eMH1 WALLBOX Installation Manual preview
eMH1 WALLBOX
Бренд: ABL Страницы: 94
Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Бренд: Bimmer Jakes Страницы: 4
Pacbrake C44059 Installation Manual preview
C44059
Бренд: Pacbrake Страницы: 14
BMW Wireless Charging Station Universal Instructions For Use Manual preview
Wireless Charging Station Universal
Бренд: BMW Страницы: 160
Curt Manufacturing 31048 Installation Instructions Manual preview
31048
Бренд: Curt Manufacturing Страницы: 6
Veigel S47290920 Installation And Operating Instructions Manual preview
S47290920
Бренд: Veigel Страницы: 24
Cellular Line interphone Instruction Manual preview
interphone
Бренд: Cellular Line Страницы: 25
Mitsubishi MIrage 2019 Owner'S Handbook Manual preview
MIrage 2019
Бренд: Mitsubishi Страницы: 19
Brink 4698 Fitting Instructions Manual preview
4698
Бренд: Brink Страницы: 26
KLAUS Multiparking trendvario6X00 Service Manual preview
trendvario6X00
Бренд: KLAUS Multiparking Страницы: 72
Mitsubishi MOTORS OUTLANDER PHEV 2022 Manual preview
OUTLANDER PHEV 2022
Бренд: Mitsubishi MOTORS Страницы: 8
Butts of Bawtry TBT4700 Quick Start Manual preview
TBT4700
Бренд: Butts of Bawtry Страницы: 2
Belkin LineCast Auto FM User Manual preview
LineCast Auto FM
Бренд: Belkin Страницы: 15
Rover 75 Saloon Owner'S Handbook Manual preview
75 Saloon
Бренд: Rover Страницы: 285
Xpresskit 20110601 Installation Manual preview
20110601
Бренд: Xpresskit Страницы: 12
Whispbar K423W Fitting Instructions Manual preview
K423W
Бренд: Whispbar Страницы: 18
Lincoln MKZ HYBRID 2016 Quick Reference Manual preview
MKZ HYBRID 2016
Бренд: Lincoln Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды