manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

EM0494

EM

−

6

−

ENGINE MECHANICAL

VALVE CLEARANCE

509

Author:

Date:

1996 LAND CRUISER   (RM451U)

S

Using SST (A), press down the valve lifter and place
SST (B) between the camshaft and valve lifter
flange. Remove SST (A).

SST

09248

−

06020, 09248

−

55050 (09248

−

05510)

HINT:

S

Apply SST (B) at slight angle on the side marked with ”11”,
at the position shown in the illustration.

S

When SST (B) is inserted too deeply, it will get pinched by
the shim. To prevent it from being stuck, insert it shallowly
from the outside of the cylinder head, at a slight angle.

S

Remove the adjusting shim with a small screwdriver and
magnetic finger.

(b)

Determine the replacement adjusting shim size by follow-
ing the Formula or Charts:

S

Using a micrometer, measure the thickness of the
removed shim.

S

Calculate the thickness of a new shim so that the
valve clearance comes within specified value.
T ....... Thickness of removed shim
A ....... Measured valve clearance
N ....... Thickness of new shim

Intake: N = T + (A 

−

 0.20 mm (0.008 in.))

Exhaust: N = T + (A 

−

 0.30 mm (0.012 in.))

S

Select a new shim with a thickness as close as pos-
sible to the calculated value.

HINT:
Shims are available in 17 sized in increments of 0.05 mm
(0.0020 in.), from 2.50 mm (0.0984 in.) to 3.30 mm (0.1299 in.).

(c)

Install a new adjusting shim.

S

Place a new adjusting shim on the valve lifter.

S

Using SST (A), press down the valve lifter and re-
move SST (B).

SST

09248

−

06020, 09248

−

55050 (09248

−

05510)

(d)

Recheck the valve clearance.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

cam 2850 Mounting Instructions preview
2850
Бренд: cam Страницы: 2
Dapper Lighting 575 Install Manual preview
575
Бренд: Dapper Lighting Страницы: 2
Hama Neptun Manual preview
Neptun
Бренд: Hama Страницы: 6
Streetwize LeisureWize EMOVE EM303A Manual preview
LeisureWize EMOVE EM303A
Бренд: Streetwize Страницы: 20
SnapPad EQ Round Installation Instructions preview
EQ Round
Бренд: SnapPad Страницы: 5
Sirius Satellite Radio Streamer GTR Installation Manual preview
Streamer GTR
Бренд: Sirius Satellite Radio Страницы: 8
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Бренд: iRacing Страницы: 25
UGREEN Car Cup Holder Phone Mount Manual preview
Car Cup Holder Phone Mount
Бренд: UGREEN Страницы: 9
Audiovox Code Alarm PROFESSIONAL SERIES CA 5550SST Owner'S Manual preview
Code Alarm PROFESSIONAL SERIES CA 5550SST
Бренд: Audiovox Страницы: 14
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Бренд: Saturn Страницы: 440
Honda 08V31-TE0-100A Installation Instructions Manual preview
08V31-TE0-100A
Бренд: Honda Страницы: 10
Hella 2DA 008 136-031 Mounting Instructions preview
2DA 008 136-031
Бренд: Hella Страницы: 2
Acura TSX 2014 Advanced Technology Manual preview
TSX 2014
Бренд: Acura Страницы: 19
Ford 2009 Edge Owner'S Manual preview
2009 Edge
Бренд: Ford Страницы: 325
Ford C-Max Energi 2014 Quick Reference Manual preview
C-Max Energi 2014
Бренд: Ford Страницы: 10
iSimple blustream Owner'S Manual preview
blustream
Бренд: iSimple Страницы: 12
Scion 2013 iQ Warranty & Maintenance Manual preview
2013 iQ
Бренд: Scion Страницы: 58
SkyRack SR-CB-101 Assembly And Instruction Sheet preview
SR-CB-101
Бренд: SkyRack Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды