manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

CH0EO

−

02

CH0712

Blue

Red

White

Charging

Necessary

OK

Add Distilled

Water

CH

−

2

−

CHARGING

CHARGING SYSTEM

1996 LAND CRUISER   (RM451U)

CHARGING SYSTEM

ON

−

VEHICLE INSPECTION

1.

CHECK BATTERY ELECTROLYTE LEVEL AND VOLT-
AGE

(a)

Check the electrolyte quantity of each cell.

If under the lower level, replace the battery (or add distilled wa-
ter if possible). check the charging system.

(b)

Measure the battery voltage between the negative (

−

)

and positive (+) terminals of the battery.

Standard voltage: At 20

°

C (68

°

F): 12.7 

−

 12.9 V

HINT:

S

Before measuring the voltage, turn the ignition switch
OFF and turn off the electrical systems (headlight, blower
motor, rear defogger etc.).

S

If the vehicle has been running, wait 20 minutes or more
after the vehicle stops before measuring the battery volt-
age.

If the voltage is less than specification, charge the battery.

HINT:
Check the indicator as shown in the illustration.

2.

CHECK BATTERY TERMINALS, FUSIBLE LINK AND
FUSES

(a)

Check that the battery terminals are not loose or cor-
roded.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

IAME Parilla X30 Assembly Instructions And User'S Manual preview
Parilla X30
Бренд: IAME Страницы: 17
GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Бренд: GOgroove Страницы: 9
Metra Electronics 70-5511 Installation Instructions preview
70-5511
Бренд: Metra Electronics Страницы: 2
Xpresskit DBALL2-HYUNDAI9 Installation And Quick Reference Manual preview
DBALL2-HYUNDAI9
Бренд: Xpresskit Страницы: 13
RAM 2011 3500 Chassis Cab User Manual preview
2011 3500 Chassis Cab
Бренд: RAM Страницы: 92
Condor T-RAMP Quick Start Manual preview
T-RAMP
Бренд: Condor Страницы: 2
Valeo Park Vision VAL632210 Instruction Manual preview
Park Vision VAL632210
Бренд: Valeo Страницы: 25
Audi Audi 80 1987 Workshop Manual preview
Audi 80 1987
Бренд: Audi Страницы: 63
Safe Fleet Prime Design OCM-3032 Quick Start Manual preview
Prime Design OCM-3032
Бренд: Safe Fleet Страницы: 4
Prorack K947 Fitting Instructions Manual preview
K947
Бренд: Prorack Страницы: 14
ECS Electronics CT-050-B1 Fitting Instructions Manual preview
CT-050-B1
Бренд: ECS Electronics Страницы: 42
Front Runner LATF002 Quick Start Manual preview
LATF002
Бренд: Front Runner Страницы: 7
Saab 32 025 687 Installation Instructions Manual preview
32 025 687
Бренд: Saab Страницы: 9
TigerTough E82201B Installation Manual preview
E82201B
Бренд: TigerTough Страницы: 7
GAC MOTOR GAC7130H2A5 User Manual preview
GAC7130H2A5
Бренд: GAC MOTOR Страницы: 356
Witter DT144AU Fitting Instructions preview
DT144AU
Бренд: Witter Страницы: 2
Automotive Data Solutions BLADE-AL-TL5-EN Install Manual preview
BLADE-AL-TL5-EN
Бренд: Automotive Data Solutions Страницы: 27
Ford F-150 Hybrid 2021 Emergency Response Manual preview
F-150 Hybrid 2021
Бренд: Ford Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды