manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

EC07H

−

06

−

EMISSION CONTROL

EMISSION CONTROL SYSTEM

EC

−

1

614

Author:

Date:

1996 LAND CRUISER   (RM451U)

EMISSION CONTROL SYSTEM

PURPOSE

The emission control systems are installed to reduce the amount of HC, CO and NOx exhausted from the
engine ((3), (4) and (5)), to prevent the atmospheric release of blow

−

by gas

−

containing HC (1) and evapo-

rated fuel containing HC being released from the fuel tank (2).
The function of each system is shown in the following table.

System

Abbreviation

Function

(1) Positive Crankcase Ventilation
(2) Evaporative Emission Control
(3) Exhaust Gas Recirculation
(4) Three

−

Way Catalytic Converter

(5) Sequential Multiport Fuel Injection*

PCV

EVAP

EGR
TWC

SFI

Reduces HC
Reduces evaporated HC
Reduces NOx
Reduces HC, CO and NOx
Injects a precisely timed, optimum amount of fuel for reduced
exhaust emissions

Remark: * For inspection and repair of the SFI system, refer to the SF section in this manual.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

RAM 2500 2020 Quick Reference Manual preview
2500 2020
Бренд: RAM Страницы: 20
Ultra Start KE-6 Owner'S Manual preview
KE-6
Бренд: Ultra Start Страницы: 8
Volkswagen 1973 Convertible Owner'S Manual preview
1973 Convertible
Бренд: Volkswagen Страницы: 80
CARRYBOY CB-796IG2-CIGD-R Installation Manual preview
CB-796IG2-CIGD-R
Бренд: CARRYBOY Страницы: 4
GMC 2012 Terrain Owner'S Manual preview
2012 Terrain
Бренд: GMC Страницы: 428
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Бренд: Chevrolet Страницы: 412
GAC MOTOR EMPOW Manual preview
EMPOW
Бренд: GAC MOTOR Страницы: 356
GMC 2013 GMC Savana Owner'S Manual preview
2013 GMC Savana
Бренд: GMC Страницы: 398
v.link VL2-MBN2 Manual preview
VL2-MBN2
Бренд: v.link Страницы: 12
WATT CARWATT CV12-220C150 User Manual preview
CARWATT CV12-220C150
Бренд: WATT Страницы: 26
Cadillac 2000 DeVille Service Manual Addendum preview
2000 DeVille
Бренд: Cadillac Страницы: 19
Pet Gear TL9000 Instruction Manual preview
TL9000
Бренд: Pet Gear Страницы: 4
Suzuki IGNIS 2022 Series Manual preview
IGNIS 2022 Series
Бренд: Suzuki Страницы: 570
Rugged Ridge 13551.33 Manual preview
13551.33
Бренд: Rugged Ridge Страницы: 3
ADAPT SOLUTIONS ASENTO EV-COLC15R Installation Manual preview
ASENTO EV-COLC15R
Бренд: ADAPT SOLUTIONS Страницы: 22
Yakima K1043 Manual preview
K1043
Бренд: Yakima Страницы: 10
Curt Manufacturing 58987 Installation Manual preview
58987
Бренд: Curt Manufacturing Страницы: 4
Rajant BreadCrumb DX2 Series Quick Start Manual preview
BreadCrumb DX2 Series
Бренд: Rajant Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды