manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

−

ENGINE MECHANICAL

ENGINE UNIT

EM

−

79

1996 LAND CRUISER   (RM451U)

16. Differential Side:

INSTALL FRONT AND REAR PROPELLER SHAFTS

(a)

Align the matchmarks on the flanges and connect the
flanges with the 4 bolts and nuts.

(b)

Torque the bolts and nuts.

Torque:
74 N·m (750 kgf·cm, 54 ft·lbf) for front shaft 
88 N·m (900 kgf·cm, 65 ft·lbf)for rear shaft

17. Transfer Side:

INSTALL FRONT AND REAR PROPELLER SHAFTS

(a)

Align the matchmarks on the flanges and connect the
flanges with the 4 nuts.

(b)

Torque the nuts.

Torque:
74 N·m (750 kgf·cm, 54 ft·lbf) for front shaft
88 N·m (900 kgf·cm, 65 ft·lbf) for rear shaft

18. INSTALL STABILIZER BAR

(a)

Temporarily install the stabilizer bar to the axle housing
with the bolt and nut.

(b)

Connect the stabilizer bar with the 2 bolts.

Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)

(c)

Bounce the vehicle up and down to stabilize the suspen-
sion.

(d)

Torque the bolt and nut holding the stabilizer bar to the
axle housing.

Torque: 25 N·m (260 kgf·cm, 19 ft·lbf)

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

B-Speech B-Speech Prim Manual preview
B-Speech Prim
Бренд: B-Speech Страницы: 18
ECS Electronics CR-066-BHU Manual preview
CR-066-BHU
Бренд: ECS Electronics Страницы: 16
B-Speech Sima User Manual preview
Sima
Бренд: B-Speech Страницы: 4
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Бренд: Ranger design Страницы: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Бренд: AUTOTECH Страницы: 1
Audiovox AA-BAT Programming Manual preview
AA-BAT
Бренд: Audiovox Страницы: 3
Victory 4x4 VRKCAP Install Instructions Manual preview
VRKCAP
Бренд: Victory 4x4 Страницы: 9
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Бренд: APS Страницы: 3
Ford FUSION 2014 Owner'S Manual preview
FUSION 2014
Бренд: Ford Страницы: 458
Elinchrom ELB 1200 User Manual preview
ELB 1200
Бренд: Elinchrom Страницы: 101
OHIOSTEEL 1084TR Quick Start Manual preview
1084TR
Бренд: OHIOSTEEL Страницы: 2
Toyota SEQUOIA 2010 Quick Reference Manual preview
SEQUOIA 2010
Бренд: Toyota Страницы: 36
Ranger design 1525-PCX Installation Manual preview
1525-PCX
Бренд: Ranger design Страницы: 22
Subaru 2015 Forester Quick Reference Manual preview
2015 Forester
Бренд: Subaru Страницы: 16
HawksHead TRACK MASTER Instruction Manual preview
TRACK MASTER
Бренд: HawksHead Страницы: 10
Telwin ST 160 Instruction Manual preview
ST 160
Бренд: Telwin Страницы: 32
Lampa SnowDrive Pilot-Pro 16270 Fitting Instructions Manual preview
SnowDrive Pilot-Pro 16270
Бренд: Lampa Страницы: 32
DV8 FBBR-03 Installation Manual preview
FBBR-03
Бренд: DV8 Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды