manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

R09496

SST

SST

SR

−

14

−

STEERING

TILT STEERING COLUMN

1996 LAND CRUISER   (RM451U)

10. REMOVE COLUMN UPPER TUBE WITH MAIN SHAFT

ASSEMBLY

(a)

Set SST, the nut (10 mm nominal diameter, 1.25 mm
pitch), plate washer (36 mm outer diameter) and bolt (10
mm nominal diameter, 1.25 mm pitch, 50 mm length), as
shown.
SST

09910

−

00015 (09911

−

00011, 09912

−

00010)

Reference
    Nut:           90170

−

10004

    Plate washer:  90201

−

10201

    Bolt:           91111

−

51050

(b)

Remove the 2 tilt No.2 bolts by using the sliding hammer
on SST.

(c)

Remove the upper tube with the shaft assembly from the
column lower tube.

11.

REMOVE TURN SIGNAL BRACKET

Remove the 2 bolts.

12. REMOVE MAIN SHAFT ASSEMBLY

(a)

Using SST, compress the compression spring.
SST

09950

−

40010 (09957

−

04010, 09958

−

04010)

NOTICE:
Do not bend the sliding yoke of the main shaft assembly
more than 20

°

.

(b)

Using snap ring pliers, remove the snap ring.

(c)

Remove the shaft assembly from the column upper tube.

(d)

Remove the compression spring, bearing thrust collar
and bearing from the shaft assembly.

13. REMOVE COLLAR

Remove the snap ring and collar from the column lower tube.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

GARO TWIN+ Assembly Instructions / End User Instruction preview
TWIN+
Бренд: GARO Страницы: 23
GARO LS4 Wallmounted Operational Instructions preview
LS4 Wallmounted
Бренд: GARO Страницы: 15
Front Runner Easy-Out Fitting Instructions preview
Easy-Out
Бренд: Front Runner Страницы: 5
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Бренд: Ford Страницы: 2
Streetwize LeisureWize EMOVE EM303A Manual preview
LeisureWize EMOVE EM303A
Бренд: Streetwize Страницы: 20
Webasto Transit Vancouver Wagon Manual preview
Transit Vancouver Wagon
Бренд: Webasto Страницы: 44
RAM 2012 Truck Chassis cab Owner'S Manual preview
2012 Truck Chassis cab
Бренд: RAM Страницы: 506
Saab 12 787 887 Installation Instructions Manual preview
12 787 887
Бренд: Saab Страницы: 12
H&S XRT Pro Installation & Operation Manual preview
XRT Pro
Бренд: H&S Страницы: 32
Edelbrock 29135 Installation Instructions preview
29135
Бренд: Edelbrock Страницы: 2
Mercedes-Benz 1989 560 SL Owner'S Manual preview
1989 560 SL
Бренд: Mercedes-Benz Страницы: 93
Xpresskit PKTX Installation Manual preview
PKTX
Бренд: Xpresskit Страницы: 12
Edelbrock Performer-Plus 2172 Installation Instructions preview
Performer-Plus 2172
Бренд: Edelbrock Страницы: 4
Porsche 928 GTS 1994 Owner'S Manual preview
928 GTS 1994
Бренд: Porsche Страницы: 127
Bulldog Security BulldogOne BD1 User Manual preview
BulldogOne BD1
Бренд: Bulldog Security Страницы: 7
DRAGONFIRE 11-0800 Installation Instructions preview
11-0800
Бренд: DRAGONFIRE Страницы: 4
Flash Cover MN012 Installation Manual preview
MN012
Бренд: Flash Cover Страницы: 2
Gigaware Gigaware 12-493 User Manual preview
Gigaware 12-493
Бренд: Gigaware Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды