manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

DI

−

336

−

DIAGNOSTICS

CRUISE CONTROL SYSTEM

1996 LAND CRUISER   (RM451U)

Actuator Control Cable

INSPECTION PROCEDURE

1

Actuator control cable inspection

CHECK:

(a)

Check that the actuator, control cable throttle link are properly installed and that the cable and link are
connected correctly.

(b)

Check that the actuator and bell crank are operating smoothly.

(c)

Check that the cable is not loose or too tight.

OK:

Freeplay: less than 10 mm

HINT:

S

If the control cable is very loose, the vehicle’s loss of speed going uphill will be large.

S

If the control cable is too tight, the idle RPM will become high.

DI5OR

−

01

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Neuspeed 25.02.22.2 Installation Instructions preview
25.02.22.2
Бренд: Neuspeed Страницы: 2
Thule 1306 RAPID SYSTEM Fitting Instructions Manual preview
1306 RAPID SYSTEM
Бренд: Thule Страницы: 8
Bestop 54822 Installation Instructions Manual preview
54822
Бренд: Bestop Страницы: 11
Whispbar K455W Fitting Instructions Manual preview
K455W
Бренд: Whispbar Страницы: 14
Vauxhall 2014 Insignia VXR SuperSport Specifications preview
2014 Insignia VXR SuperSport
Бренд: Vauxhall Страницы: 56
Vintage Air 561163 Manual preview
561163
Бренд: Vintage Air Страницы: 28
Volkswagen 1973 Convertible Owner'S Manual preview
1973 Convertible
Бренд: Volkswagen Страницы: 80
Alfa Romeo FIX&GO automatic Manual preview
FIX&GO automatic
Бренд: Alfa Romeo Страницы: 40
muth signal mirror Instalation Instructions preview
signal mirror
Бренд: muth Страницы: 10
Dodge 8W-30 Wiring Diagram preview
8W-30
Бренд: Dodge Страницы: 24
Park-Daddy PD50AA Installation Manual preview
PD50AA
Бренд: Park-Daddy Страницы: 22
aci ADARAC Aluminum M Series Installation Instructions Manual preview
ADARAC Aluminum M Series
Бренд: aci Страницы: 16
Imiola HAK-POL O/018 Quick Manual preview
O/018
Бренд: Imiola HAK-POL Страницы: 3
Pet Gear TRI-FOLD PG9300RF Instruction Manual preview
TRI-FOLD PG9300RF
Бренд: Pet Gear Страницы: 4
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Бренд: Acura Страницы: 6
Fab Fours C3150 Installation Instructions Manual preview
C3150
Бренд: Fab Fours Страницы: 21
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Бренд: Oldsmobile Страницы: 380
Oldsmobile 1994 Bravada Owner'S Manual preview
1994 Bravada
Бренд: Oldsmobile Страницы: 248

Бренды по названию

Популярные бренды

Загрузить еще бренды