background image

BR1CE

01

R13494

R00252

BR

4

BRAKE

BRAKE FLUID

986

Author:

Date:

1996 LAND CRUISER   (RM451U)

BRAKE FLUID

BLEEDING

HINT:
If any work is done on the brake system or if air is suspected in
the brake lines, bleed the system of air.

NOTICE:
Do not let brake fluid remain on a painted surface. Wash it
off immediately.

1.

FILL BRAKE RESERVOIR WITH BRAKE FLUID

Check the fluid level in the reservoir after bleeding each wheel.
Add fluid, if necessary.

Fluid: SAE J1703 or FMVSS No.116 DOT3

2.

BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir
becomes empty, bleed the air from the master cylinder.
(a)

Disconnect the brake lines from the master cylinder.

(b)

Slowly depress the brake pedal and hold it.

(c)

Block off the outlet plugs with your fingers, and release
the brake pedal.

(d)

Repeat (b) and (c) 3 or 4 times.

3.

CONNECT VINYL TUBE TO BRAKE CALIPER BLEED-
ER PLUG

Insert other end of the tube in a half

full container of brake fluid.

NOTICE:
Begin bleeding air from the brake caliper with the longest
hydraulic line.
4.

BLEED BRAKE LINE

(a)

Slowly depress the brake pedal several times.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы: