manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

Z07256

ECU Side

−

SUSPENSION AND AXLE

DIFFERENTIAL LOCKING SYSTEM

SA

−

103

960

Author:

Date:

1996 LAND CRUISER   (RM451U)

DIFF. fuse/

8 (IG)  

−

 Body ground

Ignition switch ON

Battery positive voltage

Rear diff. lock position switch/

2 (RLP) 

−

 Body ground

Ignition switch ON, 

Indicator light (Rear) ON

About 0 V

Ignition switch ON, 

Indicator light (Rear) OFF

Battery positive voltage

Front diff. lock position switch/

9 (FLP) 

−

 Body ground

Ignition switch ON, 

Indicator light (front) ON.

About 0 V

Ignition switch ON, 

Indicator light (front) OFF

Battery positive voltage

Center diff. indicator switch/

15 (4WD) 

−

 Body groud

Ignition switch ON, 

Indicator light (Center diff. lock) ON

About 0 V

Ignition switch ON, 

Indicator light (Center diff. lock) OFF

Battery positive voltage

Differential lock control switch/

12 (R) 

−

 Body ground

Ignition switch ON,

Diff. lock control switch RR or FR RR

Battery positive voltage

Ignition switch ON,

Diff. lock control switch OFF

About 0 V

Differential lock control switch/

6 (RF) 

−

 Body ground

Ignition switch ON,

Diff. lock control switch FR RR

Battery positive voltage

Ignition switch ON,

Diff. lock control switch OFF or RR

About 0 V

HINT:
When a signal enters the ECU to LOCK the front differential and
set the rear differential to FREE (when battery positive voltage
is inputted to terminal 6 (RF) of ECU and about 0 V is inputted
to terminal 12 (R)), or a signal to FREE both the front and rear
differentials, the indicator lights keep blinking until the ignition
switch is turned off (Fail

−

safe function).

If the circuit is not as specified, check and repair or replace the
trouble part shown in the table above.
(b)

Inspect the battery positive voltage

Battery positive voltage: 10 

−

 14.5 V

(c)

Inspect the system circuit with connector connected
(1)

Turn the ignition switch to the ON position.

(2)

Keep the center Diff. lock condition.

(3)

Remove the Diff. lock ECU.

(4)

Using a voltmeter, measure the voltage when the
differential lock control switch is in the position, as
shown below.

Terminals (Symbols)

Switch Position

STD Voltage (V)

15 (4WD) 

−

 13 (GND)

−

0.5 or less

9 (FLP) 

−

 13 (GND)

FR RR

0.5 or less

2 (RLP) 

−

 13 (GND)

RR or FR RR

0.5 or less

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Lancia THESIS CONNECT Owner'S Handbook Manual preview
THESIS CONNECT
Бренд: Lancia Страницы: 386
BrandMotion 1009-6503 Installation Instructions Manual preview
1009-6503
Бренд: BrandMotion Страницы: 8
Hyundai Santa Fe 2006 Owner'S Manual preview
Santa Fe 2006
Бренд: Hyundai Страницы: 280
Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne... Installation Instructions preview
LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...
Бренд: Dakota Digital Страницы: 3
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Бренд: Carcomm Страницы: 2
Yakima LowRider Manual preview
LowRider
Бренд: Yakima Страницы: 15
TEINHOF V-295 Fitting And Operation Manual preview
V-295
Бренд: TEINHOF Страницы: 2
Tesla MODEL Y Owner'S Manual preview
MODEL Y
Бренд: Tesla Страницы: 274
Lippert Stargazer Spirit XTR Skylight Installation Manual preview
Stargazer Spirit XTR Skylight
Бренд: Lippert Страницы: 8
RAM Promaster 2016 User Manual preview
Promaster 2016
Бренд: RAM Страницы: 148
Hamron 619-626 User Instructions preview
619-626
Бренд: Hamron Страницы: 36
Conrad 85 51 49 Operating Instructions Manual preview
85 51 49
Бренд: Conrad Страницы: 50
RAM RAM C 2013 Specification preview
RAM C 2013
Бренд: RAM Страницы: 5
Kuda 076100 Installation Instruction preview
076100
Бренд: Kuda Страницы: 3
Edelbrock Turbocharger 15012 Installation Instructions preview
Turbocharger 15012
Бренд: Edelbrock Страницы: 1
GMC Yukon XL Denali 2015 Owner'S Manual preview
Yukon XL Denali 2015
Бренд: GMC Страницы: 439
Istar PI00670 Instruction Manual preview
PI00670
Бренд: Istar Страницы: 6
Audiovox Electronics HR7012M Installation Manual preview
HR7012M
Бренд: Audiovox Electronics Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды