manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

P22687

P08512

IG

−

2

−

IGNITION

IGNITION SYSTEM

736

Author:

Date:

1996 LAND CRUISER   (RM451U)

2.

REMOVE NO.2 PCV HOSE

3.

REMOVE AIR CLEANER HOSE

4.

DISCONNECT THROTTLE CABLE

5.

REMOVE NO.2 AND NO.3 CYLINDER HEAD COVERS

Remove the 4 bolts and head covers.

6.

DISCONNECT HIGH

−

TENSION CORDS FROM SPARK

PLUGS

(a)

Remove the 2 mounting bolts of the No.1 and No.2 cord
clamps.

(b)

Disconnect the high

−

tension cords at the rubber boot.

Do not pull on the cords.

NOTICE:
Pulling on or bending the cords may damage the conductor
inside.

7.

DISCONNECT HIGH

−

TENSION CORDS FROM DIS-

TRIBUTOR CAP AND IGNITION COIL

(a)

Using a screwdriver, lift up the lock claw and disconnect
the holder from the distributor cap (ignition coil).

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Metra Electronics 70-5511 Installation Instructions preview
70-5511
Бренд: Metra Electronics Страницы: 2
Axxess AX-AM-AU92 Installation Instructions Manual preview
AX-AM-AU92
Бренд: Axxess Страницы: 8
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Бренд: ULTIMATE SPEED Страницы: 6
Omix-Ada 11704.05 Owner'S Manual preview
11704.05
Бренд: Omix-Ada Страницы: 6
GROM Audio VLINE Installation Manual preview
VLINE
Бренд: GROM Audio Страницы: 20
Rajant 23-100068-001 Quick Start Manual preview
23-100068-001
Бренд: Rajant Страницы: 11
Volkswagen Passat 2011 Maintenance Manual preview
Passat 2011
Бренд: Volkswagen Страницы: 188
Octocam ECO VEDR Technical Manual preview
ECO VEDR
Бренд: Octocam Страницы: 35
Front Runner TBRA020 Quick Start Manual preview
TBRA020
Бренд: Front Runner Страницы: 7
Chrysler 200 Sedan 2012 Specifications preview
200 Sedan 2012
Бренд: Chrysler Страницы: 6
Kuda 079030 Installation Instruction preview
079030
Бренд: Kuda Страницы: 2
Metra Electronics GMRC-02 Installation Instructions preview
GMRC-02
Бренд: Metra Electronics Страницы: 2
Improved Racing EFR-600-TX Quick Start Manual preview
EFR-600-TX
Бренд: Improved Racing Страницы: 11
Huawei Hall Quick Manual preview
Hall
Бренд: Huawei Страницы: 19
Motorola MT146 Owner'S Manual preview
MT146
Бренд: Motorola Страницы: 28
Bosch 0 275 007 025 Owner'S Manual preview
0 275 007 025
Бренд: Bosch Страницы: 33
JVC AP-V8E Manual preview
AP-V8E
Бренд: JVC Страницы: 1
Honeywell Intermec CV41 User Manual preview
Intermec CV41
Бренд: Honeywell Страницы: 118

Бренды по названию

Популярные бренды

Загрузить еще бренды