manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

V08067

Rotor 

mark

Cam ring 

mark

Vane plate part 

number

Vane plate length

mm (in.)

14.995 

−

 14.997

(0.59035 

−

 0.59043)

44345

−

60030

2

None

1

3

44345

−

60040

14.993 

−

 14.995

(0.59027 

−

 0.59035)

14.991 

−

 14.993

(0.59020 

−

 0.59027)

44345

−

60050

4

2

R08078

SR3776

Compressed Air

R08702

SR

−

28

−

STEERING

POWER STEERING VANE PUMP

1996 LAND CRUISER   (RM451U)

HINT:
There are 3 vane plate lengths for the following rotor and cam
ring marks.

3.

INSPECT FLOW CONTROL VALVE

(a)

Coat the valve with power steering fluid and check that it
falls smoothly into the valve hole by its own weight.

(b)

Check the valve for leakage. Close one of the holes and
apply 392 

−

 490 kPa (4 

−

 5 kgf/cm

2

, 57 

−

 71 psi) of com-

pressed air into the opposite side, and confirm that air
does not come out from the end holes.

Inscribed mark:
A, B, C, D, E or F

4.

INSPECT SPRING

Using calipers, measure the free length of the spring.

Minimum free length: 35 

−

 37 mm (1.38 

−

 1.46 in.)

If it is not within the specification, replace the spring.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

VanEssa mobilcamping V1 User Instruction preview
V1
Бренд: VanEssa mobilcamping Страницы: 8
Uebler F42 Mounting And Operating Instructions preview
F42
Бренд: Uebler Страницы: 18
Chevrolet Avalanche 2005 Owner'S Manual preview
Avalanche 2005
Бренд: Chevrolet Страницы: 494
VDO VIEWLINE 52 MM - MOUNTING 11-09 Installation Instructions preview
VIEWLINE 52 MM - MOUNTING 11-09
Бренд: VDO Страницы: 4
Safe Fleet PRIME DESIGN VRR-E-PM21 Assembly Instructions Manual preview
PRIME DESIGN VRR-E-PM21
Бренд: Safe Fleet Страницы: 12
RAM Truck Diesel Supplement 2012 Owner'S Manual preview
Truck Diesel Supplement 2012
Бренд: RAM Страницы: 174
EUFAB 16465 Operating Instructions Manual preview
16465
Бренд: EUFAB Страницы: 12
Paccar DAF CHARGEMAX 90 User Manual preview
DAF CHARGEMAX 90
Бренд: Paccar Страницы: 40
Car-Systems Parktronic system Volkswagen Golf MK7 Assembly Manual preview
Parktronic system Volkswagen Golf MK7
Бренд: Car-Systems Страницы: 10
Cadillac 2003 Seville Owner'S Manual preview
2003 Seville
Бренд: Cadillac Страницы: 402
Cobra BAK R294 Manual preview
BAK R294
Бренд: Cobra Страницы: 2
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Бренд: Havis-Shields Страницы: 1
cam PFF Series Operating Manual preview
PFF Series
Бренд: cam Страницы: 28
r.LiNK RL2-NBT Manual preview
RL2-NBT
Бренд: r.LiNK Страницы: 20
Rugged Ridge 53701.52 Installation Manual preview
53701.52
Бренд: Rugged Ridge Страницы: 5
CITROËN Jumpy Miltispace Owner'S Handbook Manual preview
Jumpy Miltispace
Бренд: CITROËN Страницы: 164
Directed MIT4 Firmware Specific Manual preview
MIT4
Бренд: Directed Страницы: 30
Intellitronix BG6003 Installation Manual preview
BG6003
Бренд: Intellitronix Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды