manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

BO48R

−

01

BO

−

84

−

BODY

FRONT SEAT (Power Adjuster Type)

1996 LAND CRUISER   (RM451U)

DISASSEMBLY

1.

REMOVE FRONT SEAT HEADREST

2.

REMOVE SIDE SUPPORT ADJUSTER KNOB

Using a screwdriver, remove the snap ring and side support ad-
juster knob.

3.

REMOVE SEATBACK BOARD

(a)

Remove the 2 screws.

(b)

Slide the board downward to remove it.

4.

REMOVE FRONT SEATBACK ASSEMBLY

(a)

Using a hog ring pliers, remove the hog ring backward of
seatback.

(b)

Remove the 4 bolts and front seatback assembly.

Torque: 30 N·m (300 kgf·cm, 22 ft·lbf)

5.

REMOVE FRONT SEAT CUSHION INNER SHIELD

6.

REMOVE FRONT SEAT INNER BELT

7.

REMOVE FRONT SEAT CUSHION SHIELD

8.

REMOVE FRONT SEAT CUSHION

(a)

Remove the 4 bolts.

Torque: 30 N·m (300 kgf·cm, 22 ft·lbf)

(b)

Disconnect the connector, then remove the front seat
cushion.

9.

REMOVE SEAT CUSHION REAR PROTECTOR

10. REMOVE RECLINING ADJUSTER INSIDE COVER

Remove the 4 screws and reclining adjuster inside cover LH
and RH.

11.

REMOVE POWER ADJUST FRONT SHIELD

Remove the 2 screws and front shield.

12. REMOVE SLIDE MOTOR

(a)

Using the 5.0 mm (0.20 in.) hexagon wrench, remove the
4 housing bracket screws.

Torque: 10 N·m (100 kgf·cm, 7.0 ft·lbf)

(b)

Hold the front seat horizontal jack screw with a plier, and
remove the 2 nuts and 2 washers.

Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf)

HINT:
At the time of installation, apply adhesive to nut.

Part No. 08833 

−

 00070, THREE BOND 1324 or equiva-

lent

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Camcar 40061 Fe Mounting Instructions preview
40061 Fe
Бренд: Camcar Страницы: 2
Wagan 2227-1 User Manual preview
2227-1
Бренд: Wagan Страницы: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Бренд: Thermo King Страницы: 2
Renault 2016 Sandero Stepway Handbook preview
2016 Sandero Stepway
Бренд: Renault Страницы: 183
TATA Motors 2013 Nano Owner'S Manual preview
2013 Nano
Бренд: TATA Motors Страницы: 136
Ford 2004 Freestar Workshop Manual preview
2004 Freestar
Бренд: Ford Страницы: 8
Intec CVD500LCD Installation And Operation Manual preview
CVD500LCD
Бренд: Intec Страницы: 16
GMC 2010 Tahoe Owner'S Manual preview
2010 Tahoe
Бренд: GMC Страницы: 120
Prime Tech H-066 User Manual preview
H-066
Бренд: Prime Tech Страницы: 6
Brodit ProClip 854208 Manual preview
ProClip 854208
Бренд: Brodit Страницы: 2
iArmor EDGE IA-W208 Manual preview
EDGE IA-W208
Бренд: iArmor Страницы: 6
AIS MAZMOD2 Manual preview
MAZMOD2
Бренд: AIS Страницы: 2
E&G Classics Black Ice Mesh Instruction Manual preview
Black Ice Mesh
Бренд: E&G Classics Страницы: 4
v.link VL2-MBN2 Manual preview
VL2-MBN2
Бренд: v.link Страницы: 12
Elinchrom ELB 1200 User Manual preview
ELB 1200
Бренд: Elinchrom Страницы: 101
Needit Park Mini User Manual preview
Park Mini
Бренд: Needit Страницы: 2
Gemini KIT ParkingSensor 814 Installation And Use Manual preview
KIT ParkingSensor 814
Бренд: Gemini Страницы: 6
Acura 08L03-TA1-200A Installation Instructions preview
08L03-TA1-200A
Бренд: Acura Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды