manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

DI

−

80

−

DIAGNOSTICS

ENGINE

1996 LAND CRUISER   (RM451U)

DTC

P0402

Exhaust Gas Recirculation Flow Excessive

Detected

CIRCUIT DESCRIPTION

Refer to DTC P0401 (Exhaust Gas Recirculation Flow Insufficient Detected) on page 

DI

−

69

.

DTC No.

DTC Detecting Condition

Trouble Area

P0402

EGR gas temp.  sensor value is high during EGR cut

−

off when

engine is cold (Race engine at about 4,000 rpm without load so
that vacuum is applied to port E)
(2 trip detection logic)

S

EGR valve stuck open

S

EGR VSV open malfunction

S

Open  in VSV circuit for EGR

S

Short  in EGR gas temp. sensor circuit

S

ECM

EGR valve is always open (2 trip detection logic)

Refer to DTC P0401 (Exhaust Gas Recirculation Flow Insufficient Detected) for the System Check Driving
Pattern and Wiring Diagram.

INSPECTION PROCEDURE

TOYOTA hand

−

held tester

1

Connect the TOYOTA hand

−

held tester and read EGR gas temp. value.

PREPARATION:

(a)

Remove the fuse cover on the instrument panel.

(b)

Connect the TOYOTA hand

−

held tester to the DLC3.

(c)

Turn ignition switch ON and push the TOYOTA hand

−

held tester main switch ON.

CHECK:

Read EGR gas temp. on the TOYOTA hand

−

held tester.

OK:

EGR gas temp.: 150

°

C (302

°

F) or less (Not immediately after driving)

HINT:
If there is a short circuit, the TOYOTA hand

−

held tester indicates Approx. 157.5

°C (315.5°F).

OK

Go to step 4.

NG

DI5PL

−

02

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

AA Products KX405 Instruction Manual preview
KX405
Бренд: AA Products Страницы: 8
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Бренд: Kolpin Outdoors Страницы: 6
Schartec CR 4 Manual preview
CR 4
Бренд: Schartec Страницы: 2
V8 equipment EBEX.2 Instruction Manual preview
EBEX.2
Бренд: V8 equipment Страницы: 17
Safe Fleet PRIME DESIGN URX-001-E Manual preview
PRIME DESIGN URX-001-E
Бренд: Safe Fleet Страницы: 8
GARO Wallbox GLB Quick Start Manual preview
Wallbox GLB
Бренд: GARO Страницы: 15
Skoda KAROQ 2017 Owner'S Manual preview
KAROQ 2017
Бренд: Skoda Страницы: 324
Mopar 2005-2009 Chrysler 300C Installation Instructions Manual preview
2005-2009 Chrysler 300C
Бренд: Mopar Страницы: 7
CITROEN 1953 Traction Avant User Manual preview
1953 Traction Avant
Бренд: CITROEN Страницы: 26
Seat Toledo 2019 Owner'S Manual preview
Toledo 2019
Бренд: Seat Страницы: 300
Black Horse Off Road TR-JECOOE Installation Instructions preview
TR-JECOOE
Бренд: Black Horse Off Road Страницы: 3
Yakima Safety Pole Quick Start Manual preview
Safety Pole
Бренд: Yakima Страницы: 4
Menabo SHADOW CADDY Fitting Instructions Manual preview
SHADOW CADDY
Бренд: Menabo Страницы: 12
BMW 316I Owner'S Handbook Manual preview
316I
Бренд: BMW Страницы: 177
Volvo FH 6X2 Specifications preview
FH 6X2
Бренд: Volvo Страницы: 3
Toyota 2004 CELICA Electric Troubleshooting Manual preview
2004 CELICA
Бренд: Toyota Страницы: 284
Chrysler 200 Convertible Specifications preview
200 Convertible
Бренд: Chrysler Страницы: 5
Honda 2013 Crosstour EX Technology Reference Manual preview
2013 Crosstour EX
Бренд: Honda Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды