manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

−

BODY ELECTRICAL

HEADLIGHT AND TAILLIGHT SYSTEM

BE

−

17

1996 LAND CRUISER   (RM451U)

(c)

Adjust headlight in horizontal alignment.

If the ”0” moves away from the mark beyond the acceptable
range, adjust the ”0” back to the mark using adjusting screw B.
HINT:
The beam angle will change about 0

°

23’ with one mark.

2.

REPLACING HEADLIGHT

(a)

Replace the headlight.

(b)

Inspect the headlight aim. Do the following before inspec-
tion.

S

Make sure the body around the headlight is not de-
formed.

S

Park the vehicle on a level spot.

S

The driver gets into the driver’s seat and puts the
vehicle in a state ready for driving (with a full tank).

S

Bounce the vehicle several times.

(c)

Adjust headlight in vertical alignment
(1)

Using adjusting screw A, adjust the headlight aim to
within the specifications.

HINT:
The beam angle will change about 0

°

11’ with one mark.

(2)

Make sure the gauge bubble is within the accept-
able range.

HINT:
If the gauge bubble is outside the acceptable range, check that
the vehicle is parked on a level place.
(d)

Readjust the headlight aim after parking the vehicle on a
level place.

(e)

Adjust the headlight in horizontal alignment.
(1)

Using adjusting screw B, adjust the headlight aim to
within the specifications.

HINT:
The beam angle will change about 0

°

23’ with one mark.

(2)

Using adjusting nut C, adjust the ”0” back to the
mark.

HINT:
For adjustment, pull nut C to the rear of the vehicle to free it. Af-
ter adjustment, check that the nut C is locked in.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

AC Schnitzer F40 Fitting Instructions Manual preview
F40
Бренд: AC Schnitzer Страницы: 16
Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Бренд: Cadillac Страницы: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Бренд: Cadillac Страницы: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Бренд: Cadillac Страницы: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Бренд: Cadillac Страницы: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Бренд: Cadillac Страницы: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Бренд: Cadillac Страницы: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Бренд: Cadillac Страницы: 438
Code 3 21 COVERT Series Installation And Operation Instructions Manual preview
21 COVERT Series
Бренд: Code 3 Страницы: 16
Vintage Air 561163 Manual preview
561163
Бренд: Vintage Air Страницы: 28
TAUBENREUTHER 29-T080301 Quick Start Manual preview
29-T080301
Бренд: TAUBENREUTHER Страницы: 8
Menabo DELTA DL FIX 209FP Fitting Instructions Manual preview
DELTA DL FIX 209FP
Бренд: Menabo Страницы: 8
Buick Electra 225 1965 Service Manual preview
Electra 225 1965
Бренд: Buick Страницы: 914
I.D. Systems Vehicle Asset Communicator User Manual preview
Vehicle Asset Communicator
Бренд: I.D. Systems Страницы: 41
Volvo M3602654 Installation Instructions Manual preview
M3602654
Бренд: Volvo Страницы: 10
Grillo PK 1400 Operator'S Manual preview
PK 1400
Бренд: Grillo Страницы: 71

Бренды по названию

Популярные бренды

Загрузить еще бренды