manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

P22215

−

DIAGNOSTICS

ENGINE

DI

−

5

1996 LAND CRUISER   (RM451U)

Terminal No.

Connection / Voltage or Resistance

Condition

2

Bus 

ę

 Line / Pulse generation

During transmission

4

Chassis Ground / 

↔

 Body Ground 1 

Ω

 or less

Always

5

Signal Ground / 

↔

 Body Ground 1 

Ω

 or less

Always

16

Battery Positive / 

↔

 Body Ground 9 

−

 14 V

Always

HINT:
If your display shows ”UNABLE TO CONNECT TO VEHICLE”
when you have connected the cable of the OBD II  scan tool or
TOYOTA hand

−

held tester to DLC3, turned the ignition switch

ON and operated the scan tool, there is a problem on the ve-
hicle side or tool side.

S

If communication is normal when the tool is connected to
another vehicle, inspect DLC3 on the original vehicle.

S

If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service  Department listed in the
tool’s instruction manual.

2.

INSPECT DIAGNOSIS (NORMAL MODE)

(a)

Check the MIL.
(1)

The MIL comes on when the ignition switch is turned
ON and the engine is not running.

HINT:
If the MIL does not light up, troubleshoot the combination meter
(See page 

BE

−

2

).

(2)

When the engine started, the MIL should go off. If
the lamp remains on, the diagnosis system has de-
tected a malfunction or abnormality in the system

(b)

Check the DTC.

NOTICE:
TOYOTA hand

−

held tester only: When the diagnosis sys-

tem is switched from normal mode to check mode,  it
erases all DTCs and freezed frame data recorded in normal
mode. So before switching modes, always check the DTCs
and freezed frame data, and note them down

(1)

Prepare the OBD II scan tool (complying with SAE
J 1978) or TOYOTA hand

−

held tester.

(2)

Connect the OBD II scan tool or TOYOTA hand

−

held tester to DLC3 in the fuse box at the lower left
of the instrument panel.

(3)

Turn the ignition switch ON and switch the OBD II
scan tool or TOYOTA hand

−

held tester switch ON.

(4)

Use the OBD II scan tool or TOYOTA hand

−

held

tester to check the DTC and freezed frame data,
note them down. (For operating instructions, see
the OBD II scan tool’s instruction book.)

(5)

See page 

DI

−

13

 to confirm the details of the 

DTCs.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

iDataLink Maestro Installation Manual preview
Maestro
Бренд: iDataLink Страницы: 9
kaarta STENCIL PRO Assembly & Use preview
STENCIL PRO
Бренд: kaarta Страницы: 29
Zavoli Bora Technical Instructions And Installation Manual preview
Bora
Бренд: Zavoli Страницы: 26
Mercedes-Benz GUARD S 500 Supplement To Operators Manual preview
GUARD S 500
Бренд: Mercedes-Benz Страницы: 30
MAXWORKS 70275 Instruction Manual & Parts Catalogue preview
70275
Бренд: MAXWORKS Страницы: 7
Renault 2016 Sandero Stepway Handbook preview
2016 Sandero Stepway
Бренд: Renault Страницы: 183
Monacor Carpower CAP-20 Quick Manual preview
Carpower CAP-20
Бренд: Monacor Страницы: 2
Porsche 01-B Web Application Manual preview
01-B
Бренд: Porsche Страницы: 313
METRON PC05T User Manual preview
PC05T
Бренд: METRON Страницы: 4
Whispbar K951W Fitting Instructions For Basic Carrier preview
K951W
Бренд: Whispbar Страницы: 15
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Бренд: Ranger design Страницы: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Бренд: AUTOTECH Страницы: 1
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Бренд: Saturn Страницы: 440
AutoLoc SB3PR Series User Manual And Installation Manual preview
SB3PR Series
Бренд: AutoLoc Страницы: 6
iQOS CCU01 Safety Warnings And Instructions preview
CCU01
Бренд: iQOS Страницы: 4
Dodge CHALLENGER HELLCAT 2017 Owner'S Manual preview
CHALLENGER HELLCAT 2017
Бренд: Dodge Страницы: 484
AD Boivin ZX2 2008 Adjustment Manual preview
ZX2 2008
Бренд: AD Boivin Страницы: 37
Yakima K1043 Manual preview
K1043
Бренд: Yakima Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды