Toyota 1996 LAND CRUISER Скачать руководство пользователя страница 190

Страница: 190 / 1381

Z06302

−

BODY ELECTRICAL

POWER WINDOW CONTROL SYSTEM

−

1996 LAND CRUISER (RM451U)

OFF

−

Continuity

DOWN

−

Continuity

Rear Right Switch (Window lock):

Switch position

Tester connection

Specified condition

−

Continuity

OFF

−

Continuity

DOWN

−

Continuity

If continuity is not as specified, replace the master switch.

INSPECT POWER WINDOW MASTER SWITCH ILLU-
MINATION

(a)

Set the window lock switch to the unlock position.

(b)

Connect the positive (+) lead from the battery to terminal
7 and the negative (

−

) lead to terminal 1, and check that

all the illuminations light up.

(c)

Set the window lock switch to the lock position, and check
that all the passenger’s power window switch illumina-
tions go out.

If operation is not as specified, replace the master switch.

Using an ammeter:
INSPECT ONE TOUCH POWER WINDOW SYSTEM

(a)

Disconnect the connector from the master switch.

(b)

Connect the positive (+) lead from the ammeter to termi-
nal 6 on the wire harness side connector and the negative
(

−

) lead to negative terminal of the battery.

(c)

Connect the positive (+) lead from the battery to terminal
13 on the wire harness side connector.

(d)

As the window goes down, check that the current flow is
up to approximately 7 A.

(e)

Check that the current increases approximately 14.5 A or
more when the window stops going down.

HINT:
The circuit breaker opens some 4

−

40 seconds after the win-

dow stops going down, so that check must be made before the
circuit breaker operates.
If the operation is as specified, replace the master switch.

Brought to you by BirfMark

Brought to you by BirfMark
Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1996 LAND CRUISER

Отзывы:

Похожие инструкции для 1996 LAND CRUISER

Бренды по названию

Популярные бренды

Toyota 1996 LAND CRUISER, Руководство пользователя

Результаты поиска

Содержание 1996 LAND CRUISER

Отзывы:

Похожие инструкции для 1996 LAND CRUISER

Бренды по названию

Популярные бренды