manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

Q07308

AT3417

OK if hot

Add if hot

AT4252

0 

−

 1 mm

Q07309

DI

−

138

−

DIAGNOSTICS

AUTOMATIC TRANSMISSION

1996 LAND CRUISER   (RM451U)

(3)

With the engine OFF, add new fluid through the oil
filler pipe.

Fluid type: ATF DEXRON 

®

II

Capacity: 
Dry fill: 11.0 liters (11.6 US qts, 9.7 Imp. qts)
Drain and refill: 1.9 liters (2.0 US qts, 1.7 Imp. qts)

(4)

Start the engine and shift the shift lever into all posi-
tions from P to L position and then shift into P posi-
tion.

(5)

With the engine idling, check the fluid level. Add
fluid up to the COOL level on the dipstick.

(6)

Check the fluid level at the normal operating tem-
perature 70 

−

 80

°

C (158 

−

 176

°

F) and add as nec-

essary.

NOTICE:
Do not overfill.

(d)

Check the fluid leaks.
Check for leaks in the transmission.

If there are leaks, it is necessary to repair or replace O

−

rings,

Seal packings, oil seals, plugs or other parts.

(e)

Inspect and adjust the throttle cable.
(1)

Check that the throttle valve is fully closed.

(2)

Check that the inner cable is not slack.

(3)

Measure the distance between the outer cable end
and stopper on the cable.

Standard distance: 0 

−

 1 mm (0 

−

 0.04 in.)

If the distance is not standard, adjust the cable by the adjusting
nuts.

(f)

Inspect and adjust the shift lever position.
When shifting the shift lever from the N position to other
positions, check that the lever can be shifted smoothly
and accurately to each position and that the position indi-
cator correctly indicates the position.

If the indicator is not aligned with the correct position, carry out
the following adjustment procedures.

(1)

Loosen the nut on the control rod.

(2)

Push the control rod fully rearward.

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Eaton Green Motion DC 22 Training preview
Green Motion DC 22
Бренд: Eaton Страницы: 65
Acura 2006 TSX Owner'S Manual preview
2006 TSX
Бренд: Acura Страницы: 2
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Бренд: Waeco Страницы: 172
STC 552-010 Installation Instructions Manual preview
552-010
Бренд: STC Страницы: 6
TATA Motors 2013 Nano Owner'S Manual preview
2013 Nano
Бренд: TATA Motors Страницы: 136
Tachosys digidl Installation Manual preview
digidl
Бренд: Tachosys Страницы: 28
Whispbar K951W Fitting Instructions For Basic Carrier preview
K951W
Бренд: Whispbar Страницы: 15
Unex OBU-352EC Quick Start Manual preview
OBU-352EC
Бренд: Unex Страницы: 30
Sagem MyCK100 User Manual preview
MyCK100
Бренд: Sagem Страницы: 10
Fisher Body FOLDING TOP 1971 Service Manual preview
FOLDING TOP 1971
Бренд: Fisher Body Страницы: 37
Manik 519952T Installation Instructions preview
519952T
Бренд: Manik Страницы: 2
Kogan CERTA CTCVINCVR14A User Manual preview
CERTA CTCVINCVR14A
Бренд: Kogan Страницы: 4
Subaru S0A367010 Installation Instructions preview
S0A367010
Бренд: Subaru Страницы: 2
Ford C-Max Energi 2014 Quick Reference Manual preview
C-Max Energi 2014
Бренд: Ford Страницы: 10
Gacell SLH 27C User Manual preview
SLH 27C
Бренд: Gacell Страницы: 25
Edelbrock Honda XR400 Instruction Supplement preview
Honda XR400
Бренд: Edelbrock Страницы: 2
Hudson Super Six 1916 Reference Book preview
Super Six 1916
Бренд: Hudson Страницы: 77
Metra Electronics 95-7617B Installation Instructions Manual preview
95-7617B
Бренд: Metra Electronics Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды