manualshive.com logo in svg

Toyota 1996 LAND CRUISER, Руководство пользователя


Поделиться
Скачать
background image

LU0817

LU08N

−

03

EM1759

P22601

Oil Pressure Gauge

P08343

Adhesive

−

LUBRICATION

OIL AND FILTER

LU

−

1

712

Author:

Date:

1996 LAND CRUISER   (RM451U)

OIL AND FILTER

INSPECTION

1.

CHECK ENGINE OIL QUALITY

Check the oil for deterioration, entry of water, discoloring or thin-
ning.
If the quality is visibly poor, replace the oil.

Oil grade:
API grade SH Energy

−

Conserving II multigrade en-

gine oil or ILSAC multigrade engine oil.
Recommended viscosity is as shown in the illustra-
tion, with SAE 5W

−

30 being the preferred engine oil.

2.

CHECK ENGINE OIL LEVEL

The oil level should be between the ”L” and ”F” marks on the dip-
stick.
If low, check for leakage and add oil up to ”F” mark.

3.

REMOVE OIL PRESSURE SWITCH, AND INSTALL OIL
PRESSURE GAUGE

4.

WARM UP ENGINE

Allow the engine to warm up to normal operating temperature.

5.

CHECK OIL PRESSURE
Oil pressure:
At idle
    29 kPa (0.3 kgf/cm

2

, 4.3 psi) or more

At 3,000 rpm
    245 

−

 490 kPa (2.5 

−

 5.0 kgf/cm

2

, 36 

−

 71 psi)

6.

REMOVE OIL PRESSURE GAUGE AND REINSTALL
OIL PRESSURE SWITCH

(a)

Remove the oil pressure gauge.

(b)

Apply adhesive to 2 or 3 threads of the oil pressure switch.

Adhesive:
Part No. 08833

−

00080, THREE BOND 1344, 

LOCTITE 242 or equivalent

(c)

Reinstall the oil pressure switch.

7.

START ENGINE AND CHECK FOR LEAKS

Brought to you by BirfMark

Brought to you by BirfMark 
 Version 1.00 - 12/21/2010

Содержание 1996 LAND CRUISER






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1996 LAND CRUISER

Mazda 2011 Tribute Brochure & Specs preview
2011 Tribute
Бренд: Mazda Страницы: 4
FABBRI PORTATUTTO 17405400 Assembly Instructions preview
17405400
Бренд: FABBRI PORTATUTTO Страницы: 2
FORM FIT SD 13R07-5 Installation Instructions preview
SD 13R07-5
Бренд: FORM FIT Страницы: 2
Thule Edge Flush Rail Instructions Manual preview
Edge Flush Rail
Бренд: Thule Страницы: 12
Metra Electronics 99-8714 Installation Instructions Manual preview
99-8714
Бренд: Metra Electronics Страницы: 8
Camoplast Polaris TATOU 4S Installation Manuallines preview
Polaris TATOU 4S
Бренд: Camoplast Страницы: 13
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Бренд: Safe Fleet Страницы: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Бренд: Honda Страницы: 4
Yutrax TX107 Operator'S Manual preview
TX107
Бренд: Yutrax Страницы: 8
Renault KANGOO BE BOP Driver'S Handbook Manual preview
KANGOO BE BOP
Бренд: Renault Страницы: 198
Safe Fleet PRIME DESIGN VRR3-FT21G-ST Manual preview
PRIME DESIGN VRR3-FT21G-ST
Бренд: Safe Fleet Страницы: 12
RAM 2013 2500 Big Horn Information preview
2013 2500 Big Horn
Бренд: RAM Страницы: 12
Lexus LS 460 2011 Owner'S Manual preview
LS 460 2011
Бренд: Lexus Страницы: 830
Altius ATHUDW-SCA User Manual preview
ATHUDW-SCA
Бренд: Altius Страницы: 16
RAWLINK 36772 Instruction Manual preview
36772
Бренд: RAWLINK Страницы: 25
Quadratec QuadraTop Adventure Top 1113.00 Series Installation Manual preview
QuadraTop Adventure Top 1113.00 Series
Бренд: Quadratec Страницы: 20
FALCON RIDGE AC-PRO-WD05 Instructions For Installation And Care preview
AC-PRO-WD05
Бренд: FALCON RIDGE Страницы: 5
Mitsubishi 1989 Galant Service Manual preview
1989 Galant
Бренд: Mitsubishi Страницы: 1273

Бренды по названию

Популярные бренды

Загрузить еще бренды